background image

 

12

Operation modes and 
setting of the COOL/
HEAT CHANGEOVER 
REMOTE CONTROL 
SWITCH

Operation modes 
that can be 
switched using the 
wireless remote 
controller

Cooling/
Program  
dry

Upper switch: 

Lower switch: 

Cooling/ 
Program dry/ 
Fan

Heating

Upper switch: 

Lower switch: 

Heating/ 
Fan

Fan

Upper switch: 

Lower switch: 

Fan only

*  AUTOMATIC OPERATION is not possible when 

the COOL/HEAT CHANGEOVER REMOTE 
CONTROL SWITCH is provided.

B.  When the COOL/HEAT CHANGEOVER 

REMOTE CONTROL SWITCH is not provided 

Using the wireless remote controller, first follow 

the below procedure to assign the privilege to 
set cool/heat operations for other units to a 
indoor unit.

Outdoor unit

Indoor unit

Assign cool/heat selection 
privilege to an indoor unit

Outdoor unit

Indoor unit

Assign cool/heat selection 
privilege to an indoor unit

BS unit

Designate the master remote controller

1

Press and hold the OPERATION MODE 

SELECTOR button on the wireless 

remote controller for about 4 seconds.

The TIMER INDICATOR LAMP (Green) on the 
displays of all the indoor units connected to the 

same outdoor unit or BS unit will start flashing.

2

Point the wireless remote controller at the 

indoor unit to which cool/heat privilege is 

to be assigned and press the OPERATION 

MODE SELECTOR button again.

Setting is complete when the TIMER INDICATOR 
LAMP (Green) on the displays of all indoor units 

you are trying to set stop flashing.

T MER INDICATOR LAMP 

Summary of Contents for BRC7M530W

































Reviews: