background image

19 

4.  INITIAL SETTING

Available functions on this remote controllers are 
differ according to the indoor unit type applied. 
Refer to the installation manual attached to the 
Wireless Receiver Kit and conduct initial setting 
according to the combination of the indoor unit.

 

„

Wireless Receiver Kit

For installation

1.  REMOTE CONTROLLER 

INITIAL SETTING

Available functions on the remote controllers are 
differ according to the indoor unit type applied. 
Refer to the following procedure and conduct initial 
set according to the combination of the indoor unit.
1)  The initial setting indication is displayed at the 

first time of the battery insertion. 

2)  Check the model name of the model nameplate, 

which is stuck on the indoor unit body. 

Refer to the following table to find the 

corresponding 4-digit initial setting value.

Indoor unit type

Indoor unit model 

name

Initial set 

value

VRV 

system

SPLIT 

system

2 x 2  
Cassette type

FXZQ*

FFA*

2110**

*:  It will be the alphabet (A, B, C, ...) and the 

number (1, 2, 3 ....).

**:  2110

Set no.
No. 0 = No sensing
No. 1 =  When use with sensor kit model 

BRYQ60AAW

1

2

Fig. 1

1.  Change the set value:

Press the 

 button to change the blinking 

digit.

2.  Determine the set value: 

Press the 

 button to determine the 

blinking digit and move to the right digit. 
Press the 

 button to move to the left 

digit.

blinking

Press the 

 button.

Press the 

 button.

3)  The initial set value is determined when the 

digit at the far right is determined. 
Then become to normal mode display.

Summary of Contents for BRC7M530W

































Reviews: