background image

3. 

Press 

 to confirm the selection.

 

Result:

   is blinking.

4. 

Press the WPS button on your communication device 
(e.g.router) within approximately 1 minute. Refer to the 
manual of your communication device. 

Result:

 The timer LED is blinking.

5. 

Press 

 to exit the menu.

Result:

 The display will return to the default screen.

Note:

 If the blinking of the timer lamp does not slow down and 

the timer lamp goes out, repeat steps 1 through 5.

If connection is still impossible, use the procedures in “To 
connect the wireless adapter to your device directly” to perform 

setting.

To connect the wireless adapter to your device 

directly

1. 

Hold 

 for at least 5 seconds in the default screen. 

Result:

 The confirmation display (menu 

 ) appears.

2. 

Press repeatedly 

 or 

 until the AP setting display 

(menu   ) appears.

3. 

Press 

 to confirm the selection.

 

Result:

   is blinking.

4. 

Connect with your smart device to the access point in the 
same way as to a standard wireless network.

• 

Select the SSID (DaikinAP*****) printed on the unit or 
in the accessory set, and enter the password.

Result:

 The operation and timer LEDs are blinking.

5. 

Press 

 to exit the menu.

Result:

 The display will return to the default screen.

6. 

Open the application and tap “Configure the wireless 
connection”, then connect to the home network following 

the instructions on the screen.

7. 

Connect your smartphone to the home network.

To reset the connection setting to the factory default

Reset the connection setting to the factory default in case you 
want to:

• 

switch between the WPS and the AP connection option,

• 

disconnect the Wi-Fi adapter and the communication device 
(e.g.router) or smart device,

• 

repeat the setting if the connection was unsuccessful.

1. 

Hold 

 for at least 5 seconds in the default screen. 

Result:

 The confirmation display (menu 

 ) appears.

2. 

Press repeatedly 

 or 

 until the A display (menu  ) 

appears.

3. 

Hold 

 for at least 2 seconds to confirm the selection.

 

Result:

   is blinking. The setting is reset to the factory default.

4. 

Press 

 to exit the menu. 

Result:

 The display will return to the default screen.

To turn off the wireless connection

You can turn off the wireless connection using:

• 

the remote controller,

• 

the wireless adapter ON/OFF button on the unit.

To use the wireless adapter ON/OFF switch

1. 

Press the wireless adapter ON/OFF switch. 

Result:

 The wireless adapter communication is OFF.

Note:

 Press the ON/OFF switch again to turn on the wireless 

adapter.

To use the remote controller

1. 

Hold 

 for at least 5 seconds in the default screen. 

Result:

 The confirmation display (menu 

 ) appears.

2. 

Press repeatedly 

 or 

 until the OFF menu appears.

3. 

Hold 

 for at least 2 seconds to confirm the selection.

 

Result:

 

 is blinking. Communication is OFF. The 

operation and timer LEDs are blinking.

4. 

Press 

 to exit the menu.

Result:

 The display will return to the default screen.

15 

01_EN_3P620957-1.indd   15

26-Jun-20   10:17:42 AM

Summary of Contents for CTXJ25TVMAW





























Reviews: