background image

14

S

HEET

 

METAL

 

PARTS

SCREWS

CLIPS

 

AND

 

SIMILAR

 

ITEMS

 

INHERENTLY

 

HAVE

 

SHARP

 

EDGES

AND

 

IT

 

IS

 

NECESSARY

 

THAT

 

THE

 

INSTALLER

 

AND

 

SERVICE

 

PERSONNEL

 

EXERCISE

 

CAUTION

.

CAUTION

Preventive maintenance is the best way to avoid unnecessary ex-
pense and inconvenience. Have this system inspected at regular
intervals by qualified service personnel, at least twice a year. Rou-
tine maintenance should cover the following items:

1. Tighten all belts, set screws, and wire connections.
2. Clean evaporator and condenser coils mechanically or with

cold water, if necessary. Usually any fouling is only matted
on the entering air face of the coil and can be removed by
brushing.

3. Lubricate motor bearings.
4. Align or replace belts as needed.
5. Replace filters as needed (see below).
6. Check for blockage of condensate drain.
7. Check power and control voltages.
8. Check running amperage.
9. Check operating temperatures and pressures.

10. Check and adjust temperature and pressure controls.
11. Check and adjust damper linkages.
12. Check operation of all safety controls.
13. Examine gas furnaces (see below and the User’s

Information Manual).

14. Check condenser fans and tighten set screws.

F

ILTERS

CAUTION

T

O PREVENT PROPERTY DAMAGE DUE TO FIRE AND LOSS OF

EQUIPMENT  EFFICIENCY  OR  EQUIPMENT  DAMAGE DUE TO DUST AND LINT

BUILD UP ON INTERNAL PARTS, NEVER OPERATE UNIT WITHOUT AN AIR

FILTER INSTALLED IN THE RETURN AIR SYSTEM.

Every application may require a different frequency of replace-
ment of dirty filters. Filters must be replaced at least every three
(3) months during operating seasons.

Dirty filters are the most common cause of inadequate heating or
cooling performance. Filter inspection should be made at least
every two months; more often if necessary because of local condi-
tions and usage.

Dirty throwaway filters should be discarded and replaced with a
new, clean filter.

Disposable return air filters are supplied with this unit. See the
unit Specification Sheet or Technical Manual for the correct size
and part number. To remove the filters, remove the filter access
panel on return side of the unit.

C

ABINET

 F

INISH

 M

AINTENANCE

Use a fine grade automotive wax on the cabinet finish to maintain
the finish’s original high luster. This is especially important in in-
stallations with extended periods of direct sunlight.

C

LEAN

 O

UTSIDE

 C

OIL

  (Q

UALIFIED

 S

ERVICER

 O

NLY

)

The coil with the outside air flowing over it should be inspected
annually and cleaned as frequently as necessary to keep the finned
areas free of lint, hair and debris.

C

ONDENSER

 F

ANS

Bearings on the condenser fan motors are permanently lubricated.
No additional oiling is required.

L

UBRICATION

The fan shaft bearings and the supply fan motor have grease fit-
tings that should be lubricated during normal maintenance checks.

F

UNCTIONAL

 P

ARTS

Refer to the unit Parts Catalog for a list of functional parts. Parts
are available from your distributor.

Summary of Contents for DCC180 Series





































Reviews: