background image

3

WARNING

If the information in these instructions is not followed 

exactly, a fire or explosion may result causing property 

damage, personal injury or loss of life. 

- do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance. 

- WHAT TO DO IF YOU SMELL GAS: 

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any 

phone in your building. 

• Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions. If 

you cannot reach your gas supplier, call the fire 

department. 

- Installation and service must be performed by a qualified 

installer, service agency or the gas supplier. 

IMPORTANT INFORMATION

WARNING

Should overheating occur or the gas supply fail to shut 

off, turn off the manual gas shutoff valve external to the 

furnace before turning off the electrical supply.

To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this product. 

For further assistance, please contact:

CONSUMER INFORMATION LINE- DAIKIN PRODUCTS

TOLL FREE

 1-877-254-4729 

(U.S. only)

email us at: 

customerservice@daikincomfort.com

fax us at:  (713) 856-1821

(Not a technical assistance line for dealers.)

Outside the U.S.,  call 1-713-861-2500

(Not a technical assistance line for dealers.)  

Your telephone company will bill you for the call.

Summary of Contents for DM80SN













































Reviews: