background image

27

2.

Connect a calibrated water manometer (or appropriate
gas pressure gauge) at either the gas valve inlet
pressure tap or the gas piping drip leg. See White-
Rodgers
36J22Y-204  gas valve figure for location of inlet
pressure tap.

OUTLET

INLET

Gas Valve ON/OFF Selector Switch

Outlet Pressure

Inlet Pressure

Regulator
Cover Screw

White-Rodgers Model 36J22Y-204

Figure 33A

OUTLET

INLET

White-Rodgers Model 36J22Y-204

Connected to Manometer

Figure 33B

NOTE:

 If measuring gas pressure at the drip leg, a field-

supplied hose barb fitting must be installed prior to making
the hose connection. If using the inlet pressure tap on the
White-Rodgers 36J22 gas valve, then use the 36G/J Valve
Pressure Check Kit, Part No. 0151K00000S.

3. Turn ON the gas supply and operate the furnace and all

other gas consuming appliances on the same gas supply
line.

4. Measure furnace gas supply pressure with burners firing.

Supply pressure must be within the range specified in the

Inlet Gas Supply Pressure

 table.

If supply pressure differs from table, make the necessary adjust-
ments to pressure regulator, gas piping size, etc., and/or con-
sult with local gas utility.

5. Turn OFF gas to furnace at the manual shutoff valve

and disconnect manometer.  Reinstall plug before turning
on gas to furnace.

6. Turn OFF any unnecessary gas appliances stated in step

3.

Gas Line

Gas
Shutoff
Valve

Gas Line 
To Furnace

Drip Leg Cap 
With Fitting

Manometer Hose

Manometer

Open To
Atmosphere

Measuring Inlet Gas Pressure (Alt. Method)

Figure 34

G

AS

 M

ANIFOLD

 P

RESSURE

 M

EASUREMENT

 

AND

 A

DJUSTMENT

Only small variations in gas pressure should be made by adjust-
ing the gas valve pressure regulator.  The manifold pressure
must be measured with the burners operating.  To measure and
adjust the manifold pressure, use the following procedure.

1. Turn OFF gas to furnace at the manual gas shutoff valve

external to the furnace.

2. Turn off all electrical power to the system.
3. Outlet pressure tap connections:

White-Rodgers 36J22 valve: Back outlet pressure test screw
(inlet/outlet pressure tap) out one turn (counterclockwise,
not more than one turn).

4. Attach a hose and manometer to the outlet pressure tap

(White-Rodgers valve).

5. Turn ON the gas supply.
6. Turn on power and close thermostat “R” and “W” contacts

to provide a call for heat.

7. Measure the gas manifold pressure with burners firing.

Adjust manifold pressure using the 

Manifold Gas Pressure

table shown on this page.

8. Remove regulator cover screw from the outlet pressure

regulator adjust tower and turn screw clockwise to increase
pressure or counterclockwise to decrease pressure.  Replace
regulator cover screw.

9. Turn off all electrical power and gas supply to the system.
10. Remove the manometer hose from the hose barb fitting

or outlet pressure tap.

11. Replace outlet pressure tap:  White-Rodgers 36J22

valve: Turn outlet pressure test screw in to seal pressure
port (clockwise, 7 in-lb minimum).

12. Turn on electrical power and gas supply to the system.
13. Close thermostat contacts “R” and “W” to energize

the valve.

Summary of Contents for DM96SE









































Reviews: