background image

INSTALLATION INSTRUCTIONS

DPICX-*A, DPICX-*B

COIL INSULATION KIT

INSTALLATION INSTRUCTIONS

IOD-7090A

09/2021

Only personnel that have been trained to install, adjust, 

service or repair(hereinafter, “service”) the equipment 

specified in this manual should service the equipment.  

The manufacturer will not be responsible for any injury 

or property damage arising from improper service or 

service procedures.  If you service this unit, you assume 

responsibility for any injury or property damage which may 

result.  In addition, in jurisdictions that require one or more 

licenses to service the equipment specified in this manual, 

only licensed personnel should service the equipment.  

 

Improper installation, adjustment, servicing or repair of 

the equipment specified in this manual, or attempting to 

install, adjust, service or repair the equipment specified in 

this manual without proper training may result in product 

damage, property damage, personal injury or death.

WARNING

Attention Installing Personnel

As a professional installer, you have an obligation to know 

the product better than the customer. This includes all 

safety precautions and related items.
Prior to actual installation, thoroughly familiarize yourself 

with this Instruction Manual. Pay special attention to all 

safety warnings. Often during installation or repair, it is 

possible to place yourself in a position which is more 

hazardous than when the unit is in operation.
Remember, it is your responsibility to install the product 

safely and to know it well enough to be able to instruct a 

customer in its safe use.
Safety is a matter of common sense...a matter of thinking 

before acting. Most dealers have a list of specific good 

safety practices...follow them.
The precautions listed in this Installation Manual are 

intended as supplemental to existing practices. However, 

if there is a direct conflict between existing practices and 

the content of this manual, the precautions listed here take 

precedence.

Safety Precautions

The following symbols and labels are used throughout this 

manual to indicate immediate or potential safety hazards. 

It is the owner’s and installer’s responsibility to read 

and comply with all safety information and instructions 

accompanying these symbols. Failure to heed safety 

information increases the risk of personal injury, property 

damage, and/or product damage.

WARNING

HIGH VOLTAGE

D

isconnect all power before servicing or 

installing this unit. Multiple power sources 

may be present. Failure to do so may cause 

property damage, personal injury or death.

  

WARNING

Do not use any parts that are not design certified by the 

manufacturer for use with this unit. Serious property 

damage, personal injury, reduced unit performance and/or 

hazardous conditions may result from the use of such non-

approved parts.

CAUTION

When installing or servicing this equipment, safety clothing, 

including hand and eye protection is strongly recommended. 

If installing in an area that has special requirements (hard 

hats, etc.) observe these requirements.

Description

The DPICX Coil Insulation Kit is applied to the bottom 

of the drain pan and top of the coil top plate in order to 

prevent possible condensation from forming. They can be 

used with cased and uncased coils, in applications where 

the unit is installed in a space where the temperature and 

humidity may exceed 86ºF and 80% RH. 

DPICX-*A

DPICX-*B

(1) Insula

on A

(1) Insula

on B

(5) Top Plate Insula

on

Summary of Contents for DPICX-A Series









Reviews: