Daikin EKHBH-BB Installation Manual Download

Page: 30 / 64

Installation manual

EKHBH/X008BB

Indoor unit for air to water heat pump system

4PW62570-1A – 01.2011

Press the

button for a minimum of 5 seconds to enter FIELD

SET MODE.
The

icon (3) will be displayed. The current selected field

setting code is indicated

;

(2), with the set value displayed to

the right

(1).

Press the

bgi

button to select the appropriate field

setting first code.

Press the

bgj

button to select the appropriate field

setting second code.

Press the

pfi

button and

pfj

button to change

the set value of the select field setting.

Save the new value by pressing the

button.

Repeat step 2 through 4 to change other field settings as
required.

When finished, press the

button to exit FIELD SET MODE.

Detailed description

[0] User permission level

If required, certain user interface buttons can be made unavailable for
the user.

Three permission levels are defined (see the table below). Switching
between level 1 and level 2/3 is done by simultaneously pressing
buttons

pfi

and

pfj

immediately followed by

simultaneously pressing buttons

and

, and keeping all 4

buttons pressed for at least 5 seconds (in normal mode). Note that no
indication on the user interface is given. When level 2/3 is selected,
the actual permission level – either level 2 or level 3 – is determined
by the field setting [0-00].

[1] Weather dependent set point

The weather dependent set point field settings define the parameters
for the weather dependent operation of the unit. When weather
dependent operation is active the water temperature is determined
automatically depending on the outdoor temperature: low outdoor
temperatures will result in warmer water and vice versa. During
weather dependent operation, the user has the possibility to shift up
or down the target water temperature by a maximum of 5°C. See the
operation manual for more details on weather dependent operation.

■

Field settings for heating operation

■

[1-00] Low ambient temperature (Lo_A): low outdoor
temperature.

■

[1-01] High ambient temperature (Hi_A): high outdoor
temperature.

■

[1-02] Set point at low ambient temperature (Lo_Ti): the
target outgoing water temperature when the outdoor
temperature equals or drops below the low ambient
temperature (Lo_A).
Note that the Lo_Ti value should be higher than Hi_Ti, as for
low outdoor temperatures (i.e. Lo_A) warmer water is
required.

■

[1-03] Set point at high ambient temperature (Hi_Ti): the
target outgoing water temperature when the outdoor
temperature equals or rises above the high ambient
temperature (Hi_A).
Note that the Hi_Ti value should be lower than Lo_Ti, as for
warmer outdoor temperatures (i.e. Hi_A) less warm water
suffices.

■

Field settings for cooling operation

■

[1-05] Weather dependent for cooling function enable (1)/
disable (0)

■

[1-06] Low ambient temperature (Lo2_A): low outdoor
temperature.

■

[1-07] High ambient temperature (Hi2_A): high outdoor
temperature.

■

[1-08] Set point at low ambient temperature (Lo2_Ti): the
target outgoing water temperature when the outdoor
temperature equals or drops below the low ambient
temperature (Lo2_A).
Note that the Lo2_Ti value should be higher than Hi2_Ti, as
for low outdoor temperatures (i.e. Lo2_A) less cold water
suffices.

■

[1-09] Set point at high ambient temperature (Hi2_Ti): the
target outgoing water temperature when the outdoor
temperature equals or rises above the high ambient
temperature (Hi2_A).
Note that the Hi2_Ti value should be lower than Lo2_Ti, as
for warmer outdoor temperatures (i.e. Hi2_A) colder water is
required.

Target water temperature

Ambient (outdoor) temperature

Shift value

Shift value

NOTICE

Changes made to a specific field setting are only stored
when the

button is pressed. Navigating to a new field

setting code or pressing the

button will discard the

change made.

INFORMATION

■