background image

Operation manual

13

EWAQ+EWYQ009~0 EWAQ+EWYQ009~013ACW1

Packaged air-cooled water chillers and packaged reversible air to

water heatpumps

4PW51588-1

M

AINTENANCE

Important information regarding the refrigerant used

This product contains fluorinated greenhouse gases covered by the
Kyoto Protocol.

Refrigerant type:

R410A

GWP

(1)

 value:

1975

(1)

 GWP = global warming potential

Periodical inspections for refrigerant leaks may be required
depending on European or local legislation. Please contact your local
dealer for more information.

Maintenance activities

In order to ensure optimal availability of the unit, a number of checks
and inspections on the unit and the field wiring have to be carried out
at regular intervals, preferably yearly. This maintenance should be
carried out by your local Daikin technician.

Besides keeping the remote controller clean by means of a soft damp
cloth, no maintenance is required by the operator.

Standstill

T

ROUBLESHOOTING

The guidelines below might help to solve your problem. If you cannot
solve the problem, consult your installer.

No readings on the remote controller (blank display)
-

Check if the mains power is still connected to your 
installation.

-

The benefit kWh rate power supply is active

One of the error codes appears

Consult your local dealer.

The schedule timer does work but the programmed actions are
executed at the wrong time (e.g. 1 hour too late or too early)

Check if the clock and the day of the week are set correctly,
correct if necessary.

D

ISPOSAL

 

REQUIREMENTS

Dismantling of the unit, treatment of the refrigerant, of oil and of other
parts must be done in accordance with relevant local and national
legislation.

Your product is marked with this symbol. This means that
electrical and electronic products shall not be mixed with
unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the
system, treatment of the refrigerant, of oil and other parts must be
done by a qualified installer in accordance with relevant local and
national legislation.

Units must be treated at a specialized treatment facility for re-use,
recycling and recovery. By ensuring this product is disposed off
correctly, you will help to prevent potential negative consequences for
the environment and human health. Please contact the installer or
local authority for more information.

During longer periods of standstill, e.g. during summer with
a heating only application or during longer periods when
there is no need of an operating unit, it is very important
NOT TO SWITCH OFF THE POWER SUPPLY towards the
unit.

Switching off the power supply stops the automatic
repetitive movement of the motor in order to prevent it from
getting jammed.

In case of a power supply failure or pump operating failure,
drain the system (as suggested in the figure below).

When water is at standstill inside the system, freezing up is
very  likely to happen and damaging the system in the
process.

A

<A

Summary of Contents for EWAQ009ACV3

















Reviews: