Daikin Exigo E1500, Installation Manual

4 About the box

Installation manual

8

EZESHP20 EZLSHP20AUAW1B

Exigo E1500 Trailer Refrigeration Unit

4P726857-1 – 2023.03

4.2

To unpack the installation kit

The installation kit should contain the following items:

d

c

b

g

j h i

k

e

r s

aq

×16

z

a

e

ar

f

h i

j g

×4

×2

×2

×2

×2

×2

×2

×2 ×2

m

×2

m q

×2

×4

l

n

d i n

o p

×6

×6

×6

t

u

v

×5

×5

×8

aa

×8

ab

×8

ac

af

ah

ai

af

aj

ak

al

ap

×30

×30

×4

×4

×4

×3

×3

×2

an

ao

w

x y

ae

×8

×8

ag

×8

ad

am

as

a

Rol (10 m) of flexible tubing (outside Ø8 mm, red color)

x

Rivet (4.8×16, large head)

b

Rol (10 m) of flexible tubing (outside Ø10 mm, black color)

y

Self-tapping screw (5.5×22, DIN 7981 FE/ZN)

c

Diesel pump

z

Self-tapping screw (5.5×22, DIN 7981 INOX A2)

d

Bracket

aa

Exigo frame bolt

e

Self-tapping screw (4.8×22, DIN 6954 INOX A2)

ab

Flat washer (Ø13×35×5, DIN 6340 INOX)

f

Lock nut (M5, DIN 985 INOX A2-70)

ac

Lock nut (M12, DIN 982 ZINC.)

g

Flat washer (Ø6×18, UNI 6593 ZNT)

ad

Upper left grid

h

Nipple (NPT ⅛" → NPT ¼")

ae

Bolt (M6×25, DIN 931 INOX A2)

i

Straight female adapter (NPS ¼" → Ø10 mm)

af

Contact washer (Ø6.1×18×1.4 INOX)

j

Adapter 90° (NPT ⅛" → Ø10 mm)

ag

Retainer washer (Ø6)

k

Bolt (M6×30, UNI 5739 INOX A2-70)

ah

Upper right grid

l

Bolt (M8×30, UNI 5739 INOX A2-70)

ai

Hexagon socket pan head screw (M6×20, UNI 7380 INOX)

m

Flat washer (Ø8×24, UNI 6593 INOX)

aj

Hexagon socket pan head screw (M5×20, UNI 7380 INOX)

n

Straight parallel male adapter (Ø10 mm → NPT ¼")

ak

Grower washer (Ø5, UNI 1751 A2-70 INOX)

o

Nipple (NPS ¼" → M16)

al

Flat washer (Ø5×10, UNI 6592 INOX)

p

Diesel pre-filter with water separator

am

IoT module

q

Lock nut (M8, INOX)

an

Cable gland 80722

r

Straight female adapter (NPS ¼" → Ø8 mm)

ao

Hydraulic thread sealant (Loctite 542)

s

Straight parallel male adapter (Ø8 mm → NPT ¼")

ap

Box

t

Cable tie support

aq

Bottom air intake

u

Cable tie

ar

Lock nut (M6, DIN 985 INOX A2-70)

v

Self-tapping screw (4.2×16, DIN 7981)

as

Hexagon socket pan head screw (M6×16, UNI 7380 INOX)

w

Heat shield (between muffler and cold room) with Ø7 mm
holes

INFORMATION

The installation kit contains only fasteners for installing the
unit on the cold room. All fasteners and brackets needed to
install  the  fuel  supply  system  on  the  trailer  must  be
provided by the coachbuilder.

4.3

To unpack the unit

The packaging consists of a metal pallet on which the unit is fixed in
upright position, wrapped in plastic film.

The  Bottom  plate  of  the  unit  is  not  installed,  it  is  deliverabled
separately together with the necessary screws to attach it to the unit
(see 

"7.2.3 To install the unit on the cold room"

 [

4

 13]).

1

Bring out the unit that is mounted on the special transport pallet.
Use a forklift or a lifting device.

a