background image

English

14

After piping is finished, cut the removed penetration cover along the shape of piping, and install.
Also, for top panel penetration cover, as it was before removed, put the horizontal blade motor and ther-
mistor lead through the clamp of the top panel penetration cover and fix. 

(Refer to Fig. 16 and Fig. 19)

When doing this, block any gaps between the piping penetration cover and the piping using putty to pre-
vent dust from entering the indoor unit.

* Before brazing refrigerant piping, have nitrogen flow through the refrigerant piping and substitute air with 

nitrogen. Then, carry out brazing (NOTE 2). 

(Refer to Fig. 20)

 After all the brazing works are finished, carry 

out flare connection with the indoor unit.

NOTE

1.

The proper pressure for having nitrogen flow through the piping is approximately 0.02MPa, a pressure that 
makes one feel like breeze and can be obtained through a pressure reducing valve.

2.

Do not use flux when brazing refrigerant piping. Use phosphor copper brazing filler metal (BCuP-2: JIS Z 
3264/B-Cu93P-710/795: ISO 3677) that does not require flux. (If chlorinated flux is used, the piping will be 
corroded and, in addition if fluorine is contained, the refrigerant oil will be deteriorated and the refrigerant 
circuit will be affected badly.)

3.

When carrying out leakage test of refrigerant piping and the indoor unit after the installation of indoor unit 
is finished, confirm the connecting outdoor unit installation manual for test pressure. Refer to also the out-
door unit installation manual or technical document for refrigerant piping.

4.

In case of refrigerant shortage due to forgetting additional refrigerant charge etc., it will result in malfunc-
tion such as does not cool or does not heat. Refer to the outdoor unit installation manual or technical doc-
ument for refrigerant piping.

CAUTION

Do not use antioxidant when brazing piping.

It may result in malfunction of components and clogging of piping due to residue.

Thermistor lead

Horizontal blade motor lead

Top panel penetration 
cover clamp part

Fig. 19

View from air inlet side

Pressure reducing valve

Brazing place

Taping

Stop valve

Nitrogen

Nitrogen

Refrigerant piping

Fig. 20

01_EN_3P249378-6L.fm  Page 14  Sunday, September 30, 2012  2:30 PM

Summary of Contents for FHQ35CAVEB





































Reviews: