background image

40

Care

Care

 

„

Filter (small)

* For the applicable filter type, please refer to 

 Page  38

.

Attaching

1. 

Open the front panel and 

pull out the air filters. 

 Page  39

2. 

Insert the filter.

• 

Check that the filters are inserted securely under the tabs.

Air filters

Filter (small)

Filter frame

Tab

Claw

Cleaning and Replacement

1. 

Open the front panel and 

pull out the air filters. 

 Page  39

2. 

Take off the filter. 

• 

Hold the recessed parts of the frame and 

 

unhook the 4 claws.

• 

Remove the filters from the tabs.

Air filters

Filter (small)

Filter frame

Tab

Claw

3. 

Clean or replace.

[Cleaning]

  

Deodorizing filter (enzyme blue) : Blue 

/ Titanium apatite deodorizing filter : 

Blue-Black

3-1 

Vacuum dust, and soak in lukewarm 

water or water for about 10 to 

15 minutes if very dirty.

3-2 

After washing, shake off remaining 

water and let them dry in the shade.

• 

This filter can be renewed by washing it with water 
once 

every 6 months

 and we recommend 

replacing it once 

every 3 years

.

• 

Do not wiring out the filter when removing water from it.

  

Air quality filter (enzyme blue with 

PM 2.5) : Blue-White/ Dust collection 

filter (PM 2.5) : White

• 

Do not wash the filters as this will reduce their efficiency.

• 

It is recommended to replace it once 

every 6 months

.

[Replacement]

Remove the filter from the filter
frame and prepare a new one.

• 

Do not throw away the filter frame.

• 

Reuse the filter frame when replacing the filter.

• 

When attaching the filter, check that the filter is 

properly set in the tabs.

4. 

Set the filters as they were 

and close the front panel.

• 

Press the front panel at both sides and the center.

NOTE

• 

Operation with dirty filters:

− cannot deodorise the air,
− cannot clean the air,
− results in poor heating or cooling,
− may cause odour.

• 

Dispose of old filters as non-flammable waste.

01_EN_3P651499-7C.indd   40

17-Oct-22   4:56:06 PM

Summary of Contents for FTXM20W2VMA

































































































Reviews: