Daikin FTXS09HVJU Service Manual Download

Page: 7 / 274

Safety Considerations

SiUS04-904

vi Safety Considerations

SAFETY CONSIDERATIONS

Read these

SAFETY CONSIDERATIONS

carefully before

performing any repair work. Comply with these safety
symbols without fail.

Meanings of

DANGER

WARNING

CAUTION

, and

NOTE

Symbols:

DANGER

.............. Indicates an imminently hazardous

situation which, if not avoided, will
result in death or serious injury.

WARNING

............ Indicates a potentially hazardous

situation which, if not avoided, could
result in death or serious injury.

CAUTION

............. Indicates a potentially hazardous

situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.

NOTE

.................. Indicates situations that may result

in equipment or property-damage
accidents only.

1.1

Safety Considerations for Repair

DANGER

• If refrigerant gas leaks during repair or service,

ventilate the area immediately. Refrigerant gas may
produce toxic gas if it comes into contact with flames.
Refrigerant gas is heavier than air and replaces
oxygen. In the event of an accident, a massive leak
could lead to oxygen depletion, especially in
basements, and an asphyxiation hazard could occur
leading to serious injury or death.

• Do not start or stop the air conditioner operation by

plugging or unplugging the power cable plug if a
plug is used. Plugging or unplugging the power
cable plug to operate the equipment may cause an
electrical shock or fire.

• Use parts listed in the service parts list and

appropriate tools to conduct repair work. The use of
inappropriate parts or tools may cause an electrical
shock or fire.

• Disconnect power before disassembling the

equipment for repairs. Working on the equipment
that is connected to the power supply may cause an
electric shock. If it is necessary to supply power to
the equipment to conduct repairs or to inspect the
circuits, do not touch any electrically charged
sections of the equipment.

• The step-up capacitor supplies high-voltage

electricity to the electrical components of the
outdoor unit. Discharge the capacitor completely
before conducting repair work. A charged capacitor
may cause an electrical shock.

• If refrigerant gas is discharged during repair work,

do not touch the discharged refrigerant gas. The
refrigerant gas may cause frostbite.

• Use only pipes, flare nuts, tools, and other materials

designed specifically for R410A refrigerant systems.
Never use tools or materials designed for R22
refrigerant systems on an R410A refrigerant system.
Doing so can cause a serious accident or an
equipment failure.

• Check to see if the parts and wires are mounted and

connected properly, and if the connections at the
soldered or crimped terminals are secure. Improper
installation and connections may cause excessive
heat generation, fire, or electrical shock.

WARNING

• Prior to disconnecting the suction or discharge pipe

from the compressor at the welded section,
pump-down the refrigerant gas completely in a well-
ventilated place first. If there is refrigerant gas or oil
remaining inside the compressor, the refrigerant gas or
oil can discharge when the pipe is being disconnected
and it may cause an injury.

• Wear a safety helmet, gloves, and a safety belt when

working at an elevated height of more than 6.5 ft (2 m).
Insufficient safety measures may cause a fall resulting
in injury.

• Do not mix air or gas other than the specified

refrigerant R410A to the refrigerant system. If air
enters the refrigerant systems, it can cause an
excessive high pressure resulting in equipment
damage and injury.

• When relocating the equipment, check if the new

installation site has sufficient strength to withstand
the weight of the equipment. If the installation site
does not have sufficient strength and the equipment
is not properly secured, the equipment may fall and
cause injury.

• Securely fasten the outside unit terminal cover

(panel). If the terminal cover/panel is not fastened
properly, dust or water may enter the outside unit
causing fire or electric shock.

• When relocating the system, keep the refrigerant

circuit free from substances other than the specified
refrigerant (R-410A) such as air. Any presence of air
or other foreign substance in the refrigerant circuit
can cause an abnormal pressure rise or rupture,
resulting in injury.

• If refrigerant gas leaks, locate the leaking point and

repair it before charging refrigerant. After charging
refrigerant, check for refrigerant leaks. If the leaking
point cannot be located and the repair work must be
stopped, perform a pump-down and close the
service valve to prevent the refrigerant gas from
leaking into the room. The refrigerant gas itself is
harmless, but it may generate toxic gases if it comes
into contact with flames.