background image

5 Unit installation

Installation and operation manual 

11

FWE-F
Fan coil units
3P756931-1 – 2023.11

e f

a b c d

a

Heating air purge

b

Cooling air purge

c

Hot water inlet (DN3/4ʺ)

d

Hot water outlet (DN3/4ʺ)

e

Cold water inlet (DN3/4ʺ)

f

Cold water outlet (DN3/4ʺ)

To fill the water circuit

a

b

c

a

Air purge

b

Pressure relief valve

c

Cap

During filling, it might not be possible to remove all air in the system.
Remaining air can be removed during the first operating hours of the
unit.  The  air  can  be  removed  from  the  unit  through  the  manual  air
purge valve.

1

Open the cap.

2

Push  the  pressure  relief  valve  to  purge  air  from  the  unit  water
circuit(s).

3

Close the cap.

4

Additional  filling  with  water  afterwards  might  be  required  (but
never through the air purge valve).

NOTICE

Air  in  the  water  circuit  can  cause  malfunctioning.  During
filling, it may not be possible to remove all the air from the
circuit.  Remaining  air  will  be  removed  through  the
automatic air purge valves during the initial operating hours
of  the  system.  Additional  filling  with  water  afterwards  may
be required.

NOTICE

Make  sure  water  quality  complies  with  EU  directive
2020/2184.

5.5

Drain piping installation

5.5.1

Guidelines when installing the drain
piping

General guidelines

Pipe length.

 Keep drain piping as short as possible.

Pipe size.

 Keep the pipe size equal to or greater than that of the

connecting  pipe  (vinyl  pipe  of  25  mm  nominal  diameter  and
32 mm outer diameter).

Condensation.

  Take  measures  against  condensation.  Insulate

the complete drain piping in the building.

Slope.

 Make sure the drain piping slopes down (at least 1/50) to

prevent air from being trapped in the piping. Use hanging bars as
shown.

b

a

a

Hanging bar
Allowed
Not allowed

5.5.2

Connecting the drain piping

To connect the drain piping

NOTICE

Incorrect  connection  of  the  drain  hose  might  cause  leaks,
and damage the installation space and surroundings.

1

Push the drain hose as far as possible over the drain socket.

2

Tighten the screw from drain hose to drain pan’s surface.

3

Check for water leaks.

a

a

Drain socket

4

Insert  the  drain  hose  and  tighten  with  fixing  screw  (accessory
set).

Summary of Contents for FWE04FF/T

























Reviews: