Daikin McQuay MicroTech III Manual Download | Manualshive

Page: 21 / 35

background image

21

ED 15121

Chiller Enable Output

Keypad Menu Path

Main Menu_View/Set Unit_Status/Settings_Netwrk En SP=

This read only holding register indicates if operation of the chiller is disabled or enabled. If the chiller is disabled, it
cannot run. If it is enabled, it is allowed to run.

Data Type

Holding Register

Measurement

Units

Valid Range

RO Holding Register

2

Chiller state

N/A

0=Disable
1=Enable

Chiller Enable Setpoint

Keypad Menu Path

No Keypad Equivalent

This read/write holding register is used enable the chiller to run if operating conditions are satisfied, or disables the
chiller from running. The default is Null which will cause Disable to be used provided nothing else is writing to this
point. This register is ignored by the chiller application if Chiller Local/Remote is set to Local.

Data Type

Holding Register

Measurement

Units

Valid Range

RW Holding Register

9

Chiller State

N/A

0=Disable
1=Enable
2=Null

Chiller Local/Remote

Keypad Menu Path

No Keypad Equivalent

This read only holding register indicates whether the chiller is in local control or allowed to be controlled remotely over
the network. The value can only be changed locally. The values from the following variables are ignored in the chiller
application if this variable is set to Local (1):

•

Chiller Enable Setpoint

•

Chiller Mode Setpoint – Network

•

Cool Setpoint Network

•

Ice Setpoint Network

•

Capacity Limit Setpoint

•

Clear Alarm Network

Data Type

Holding Register

Measurement

Units

Valid Range

RO Holding Register

1

Mode N/A

0=Remote
1=Local

Chiller Location

Keypad Menu Path

No Keypad Equivalent

These read/write holding registers provides a description of the location. If the location is changed via Modbus, the
change is written immediately to the unit controller. However, if the location is changed by an outside source (other
than Modbus), then change will not be available via Modbus until power is cycled.

Data Type

Holding Register

Measurement

Units

Valid Range

RW Holding Register

318-327

Location N/A

ASCII String up to 20
characters. The string
cannot contain “ or $
characters.

Chiller Mode Output

Keypad Menu Path

Main Menu_View/Set Unit_Status/Settings_Netwrk Mode SP=

This read only holding register indicates the current operating mode of the chiller.

Data Type

Holding Register

Measurement

Units

Valid Range

RO Holding Register

11

HVAC mode

N/A

1=Ice
2=Cool
3=Heat
4=Cool/Heat
Recovery
5=Defrost

«
...
19
20
21
22
23
...
»

Summary of Contents for McQuay MicroTech III




































Reviews:

No comments

Related manuals for McQuay MicroTech III

Brand: Pattfield Ergo Tools Pages: 128

Brand: Jensen Pages: 70

Brand: Daikin McQuay Pages: 84

Brand: Scheppach Pages: 56

Brand: Scheppach Pages: 184

Brand: Skope Pages: 15

Brand: Filtrine Pages: 33

Brand: Powermate Pages: 20

HYDROPONIC HY 1000

Brand: TecoPonic Pages: 98

Maxxum HCCA Series

Brand: Trane Pages: 20

Agri-Fab 45-0356

Brand: SpeedEPart Pages: 8

Brand: Yard Machines Pages: 24

Brand: Yardworks Pages: 86

Brand: lancer Pages: 27

Brand: Jensen Pages: 41

AGTN1DKH Series

Brand: Samsung Pages: 44

Brand: Poulan Pro Pages: 28

Brand: Cub Cadet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands