background image

15 Relocation

Installation and operation manual

31

RKXYQ5T7Y1B
VRV IV compressor unit for indoor installation
4P408443-1 – 2015.07

14.2.10 Symptom: Noise of air conditioners

(Indoor unit, compressor unit, heat
exchanger unit)

▪ A  continuous  low  hissing  sound  is  heard  when  the  system  is  in

cooling  or  defrost  operation.  This  is  the  sound  of  refrigerant  gas
flowing  through  the  compressor  unit,  heat  exchanger  unit  and
indoor units.

▪ A  hissing  sound  which  is  heard  at  the  start  or  immediately  after

stopping  operation  or  defrost  operation.  This  is  the  noise  of
refrigerant caused by flow stop or flow change.

14.2.11 Symptom: Noise of air conditioners

(compressor unit, heat exchanger unit)

When the tone of operating noise changes. This noise is caused by
the change of frequency from the compressor or the fans.

14.2.12 Symptom: Dust comes out of the heat

exchanger unit

When  the  unit  is  used  for  the  first  time  in  a  long  time.  This  is
because dust has gotten into the heat exchanger unit.

14.2.13 Symptom: The units can give off odours

The  unit  can  absorb  the  smell  of  rooms,  furniture,  cigarettes,  etc.,
and then emit it again.

14.2.14 Symptom: The heat exchanger unit fan

does not spin

During  operation.  The  speed  of  the  fan  is  controlled  in  order  to
optimise product operation.

14.2.15 Symptom: The display shows "88"

This  is  the  case  immediately  after  the  main  power  supply  switch  is
turned  on  and  means  that  the  user  interface  is  in  normal  condition.
This continues for one minute.

14.2.16 Symptom: The compressor in the

compressor unit does not stop after a
short heating operation

This is to prevent refrigerant from remaining in the compressor. The
unit will stop after 5 to 10 minutes.

14.2.17 Symptom: The inside of an compressor

unit is warm even when the unit has
stopped

This is because the crankcase heater is warming the compressor so
that the compressor can start smoothly.

14.2.18 Symptom: Hot air can be felt when the

indoor unit is stopped

Several  different  indoor  units  are  being  run  on  the  same  system.
When another unit is running, some refrigerant will still flow through
the unit.

15

Relocation

Contact  your  dealer  for  removing  and  reinstalling  the  total  unit.
Moving units requires technical expertise.

16

Disposal

This  unit  uses  hydrofluorocarbon.  Contact  your  dealer  when
discarding  this  unit.  It  is  required  by  law  to  collect,  transport  and
discard  the  refrigerant  in  accordance  with  the  "hydrofluorocarbon
collection and destruction" regulations.

Summary of Contents for RKXYQ5T7Y1B

































Reviews: