Daikin UATN60CGXY1, Technical Manual

8

Application Information

Installation Guideline

Safety Precautions

This manual provides the procedures of installation to ensure a safe and good standard of operation for the 

air conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for 

commercial use by lay persons.

This appliance is not intended for use by persons, including children, with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 

concerning use of the appliance by a person responsible for their safety. 

Children should be supervised to ensure that they do not play with the appliance.

SAFETY PRECAUTIONS

WARNING

● Installation and maintenance should be performed by 

  qualified persons who are familiar with local code and 

  regulation, and experienced with this type of appliance.

● All field wiring must be installed in accordance with the 

  national wiring regulation.

● Ensure that the rated voltage of the unit corresponds 

  to that of the name plate before commencing wiring 

  work according to the wiring diagram.

● The  unit  must  be  GROUNDED  to  prevent  possible 

  hazard due to insulation failure.

● All  electrical  wiring  must  not  touch  the  refrigerant 

  piping, or any moving parts of the fan motors.

● Confirm that the unit has been switched OFF before 

  installing or servicing the unit.

● Disconnect  from  the  main  power  supply  before 

  servicing the air conditioner unit.

● DO  NOT  pull  out  the  power  cord  when  the  power  is 

  ON. This may cause serious electrical shocks which 

  may result in fire hazards.

● Keep the indoor and outdoor units, power cable and 

  transmission wiring, at least 1m from TVs and radios, 

  to prevent distorted pictures and static. {Depending on 

  the type and source of the electrical waves, static may 

  be heard even when more than 1m away}.

IMPORTANT

ENGLISH

Important information regarding the refrigerant 

used

This product contains fluorinated greenhouse gases. Do 

not vent gases into the atmosphere.

Refrigerant type:  R410A

GWP 

(1)

 value: 

2087.5

(1)

 GWP = global warming potential

The refrigerant quantity is indicated on the unit name 

plate. Periodical inspections for refrigerant leaks may 

be required depending on European or local legislation. 

Please contact your local dealer for more information.

NOTICE

Disposal Requirement

Dismantling of the unit, treatment of the refrigerant, oil and other parts must be done in accordance with the applicable 

legislation.

CAUTION

Please take note of the following important points

when installing.

● 

Do not install the unit where leakage of flammable

  gas may occur.

If gas leaks and accumulates around the unit, 

it may cause fire ignition.

● 

Ensure that drainage piping is connected properly.

If the drainage piping is not connected 

properly,  it  may  cause  water  leakage  which 

will dampen the furniture.

● 

Do not overcharge the unit.

This unit is factory pre-charged. 

Overcharge will cause over-current or damage 

to the compressor.

● 

Ensure that the unit’s panel is closed after service  

  or installation.

Unsecured panels will cause the unit to 

operate noisily.

● 

Sharp edges and coil surfaces are potential 

  locations which may cause injury hazards. Avoid  

  from being in contact with these places.

● 

Before turning off the power supply, set the remote

  controller’s ON/OFF switch to the “OFF” position  

  to prevent the nuisance tripping of the unit.

 If this is  

  not done, the unit’s fans will start turning automatically  

  when power resumes, posing a hazard to service 

  personnel or the user.

● 

Do not operate any heating apparatus too close to the

  air conditioner unit.

● 

Don’t use joined and twisted wires for incoming

  power supply.

● 

The equipment is not intended for use in a potentially  

  explosive atmosphere.

● 

Used only NITROGEN for air tight test.

● 

Strictly do not charge OXYGEN or ACETYLENE into the 

  unit for any purpose.