background image

Original instructions

Installation manual

19

We reserve the right to make changes without any prior notice.

UATYQ*Y1

Packaged Rooftop

4P522681-1A

CODE

DESCRIPTION

MAIN CAUSES

CHECKS AND TROUBLESHOOTING RESET UNIT 

OFF

ITEMS OFF

AL33

Compressor 3 

Overload

Intervention of the thermal 

protection compressor 3

Check working conditions.

M

No

Compressor 3

Check cabling, terminals and circuit 

breaker of the motor.

Check adsorbed current.

Check compressor discharge 

temperature.

AL34

Compressor 4 

Overload

Intervention of the thermal 

protection compressor 4

Check working conditions.

M

No

Compressor 4

Check cabling, terminals and circuit 

breaker of the motor.

Check adsorbed current.

Check compressor discharge 

temperature.

AL35

Compressor 3 

maintenance

It has been exceeded 

compressor 3 operating hours 

threshold.

Check the working conditions of the 

compressor.

M (1)

No

None

AL36

Compressor 4 

maintenance

It has been exceeded 

compressor 4 operating hours 

threshold.

Check the working conditions of the 

compressor.

M (1)

No

None

AL37-

65

Not used

-

-

-

-

-

AL66

WARNING Circuit 

1 in Prevent

Condensing pressure circuit 

1 is higher than prevention 

value (cooling mode) 

Evaporation pressure circuit 1 

is lower than prevention value 

(heating mode)

Check working conditions.

A (2)

No

One compressor of 

circuit 1

Check condensing pressure.

Check condensing fans and coil.

Check condensing coil air flow.

Check refrigerant charge

AL67

WARNING Circuit 

2 in Prevent

Condensing pressure circuit 

2 is higher than prevention 

value (cooling mode) 

Evaporation pressure circuit 2 

is lower than prevention value 

(heating mode)

Check working conditions.

A (2)

No

One compressor of 

circuit 2

Check condensing pressure.

Check condensing fans and coil.

Check condensing coil air flow.

Check refrigerant charge

AL68

Differential probe 

supply

The value measured from 

the supplyn air differential 

pressure probe for the return 

is outside the allowed range.

Check airflow.

A (2)

No

None

Check airflow distribution system.

Check supply differential pressure 

switch and its own connection hoses.

AL69

Differential probe 

return

The value measured from the 

return air differential pressure 

probe for the return is outside 

the allowed range.

Check airflow.

A (2)

No

None

Check airflow distribution system.

Check supply differential pressure 

switch and its own connection hoses.

AL70

B9 probe broken or 

disconnected

The reading of the probe 

B9 (indoor air CO2 or VOC) 

exceeds the range

Check working conditions.

M

No

All components 

and fuctions 

directly related to 

the probe

Check in the controller for the correct 

probe reading range .

Check the correct reading of the probe 

and eventually replace it.

Check probe wiring and terminals.

Check correct functioning of the 

analogic input of the main board.

AL71

B10 probe broken 

or disconnected

The reading of the probe B10 

(outdoor air relative humidity) 

exceeds the range

Check working conditions.

M

No

All components 

and fuctions 

directly related to 

the probe

Check in the controller for the correct 

probe reading range .

Check the correct reading of the probe 

and eventually replace it.

Check probe wiring and terminals.

Check correct functioning of the 

analogic input of the main board.

Summary of Contents for UATYQ25ABAY1

























Reviews: