Daikin VAM-J8 Series, Installation And Operation Manual

13Configuration

Installation and operation manual

20

VAM350~2000J8VEB

Heat reclaim ventilation unit

4P664011-1 – 2021.08

13.2

Field settings

Refer to the installer and user reference guide of the user interface for more information on how to change field settings.

Mode

SW

SW description

SW position

(a)

01

02

03

04

05

06

07

08

09

10

11

12

13

14

15

17(27)

0

Filter cleaning time

±2500 hours

±1250 hours

—

—

—

—

—

—

—

—

—

—

—

—

—

1

Nighttime free cooling timer (after stop)

(b)

OFF

ON after 2 hours

ON after 4 hours

ON after 6 hours

ON after 8 hours

—

—

—

—

—

—

—

—

—

—

2

Precool/preheat

(c)

OFF

ON

—

—

—

—

—

—

—

—

—

—

—

—

—

3

Precool/preheat duration

(c)

30 minutes

45 minutes

60 minutes

—

—

—

—

—

—

—

—

—

—

—

—

4

Initial fan speed

(d)

High

Ultra-high

—

—

—

—

—

—

—

—

—

—

—

—

—

5

(e)

Yes/No setting for duct connection with VRV

system

Without duct

With duct

Without duct

With duct

Without duct

With duct

—

—

—

—

—

—

Setting for cold areas (fan operation when

heater thermostat is OFF)

(f)

—

—

Stop/Stop

Low/Low

Stop/stop

Low/Low

—

—

—

—

—

—

—

—

—

Fan operation during defrost/oil return/hot

start

(f)

—

—

Stop/Stop

Stop/Stop

Stop/Stop

Stop/Stop

Stop/—

Stop/Stop

Stop/—

—

—

—

—

—

—

17(27)

6

Nighttime free cooling (fan settings)

(b)

High

Ultra-high

—

—

—

—

—

—

—

—

—

—

—

—

—

7

Target temperature for independent nighttime

free cooling

(b)

18°C

19°C

20°C

21°C

22°C

23°C

24°C

25°C

26°C

27°C

28°C

29°C

30°C

—

—

8

Central zone link

No

Yes

—

—

—

—

—

—

—

—

—

—

—

—

—

9

Preheat time extension

(c)

0

minutes

30

minutes

60

minutes

90

minutes

—

—

—

—

—

—

—

—

—

—

—

18(28)

0

External signal

(g)

 JC/J2

Last command

Priority on

external input

Priority on

operation

Disable nighttime

free cooling/

Perform forced

stop

—

24 hours

ventilation ON/

OFF

Disable JC/J2

—

—

—

—

—

—

—

—

1

Direct power ON

OFF

ON

—

—

—

—

—

—

—

—

—

—

—

—

—

2

Auto restart

(h)

OFF

ON

—

—

—

—

—

—

—

—

—

—

—

—

—

3

Output signal to external damper (X24A)

—

—

Damper output

(fan operation)

Damper output

(fan operation)

—

—

—

—

—

—

—

—

—

—

—

4

Indication of ventilation mode

ON

OFF

—

—

—

—

—

—

—

—

—

—

—

—

—

18(28)

6

Automatic ventilation air flow mode

Linear

—

Fixed A

Fixed B

—

—

—

—

—

—

—

—

—

—

—

7

Fresh-up mode

Supply – no

indication

Exhaust – no

indication

Supply –

indication

Exhaust –

indication

—

—

—

—

—

—

—

—

—

—

—

8

External input terminal function selection

(i)

 (JC/

J1)

Fresh-up

Error output

Error output and

stop operation

Forced off

Fan forced off

Air-flow up

—

—

—

—

—

—

—

—

—

9

BRP4A50A output switching selection

(between X3 and X4)

Heater output

Error output

Fan output (Low/

High/Ultra-high)

Fan output (High/

Ultra-high)

Fan output (Ultra-

high)

Fan output (Low/High/Ultra-high)

—

—

—

—

—

—

—

—

(between X1 and X2)

Operation output

Operation output

—

—

—

—

—

—

—

—

—

—

10

EKVDX connected?

(j)

No

Yes

—

—

—

—

—

—

—

—

—

—

—

—

—

18(28)

11

Filter contamination check

No action

Reset filter check

Force filter check

—

—

—

—

—

—

—

—

—

—

—

—

13

Cooling set point (with EKVDX)

13°C

15°C

16°C

17°C

18°C

19°C

20°C

21°C

22°C

23°C

24°C

25°C

26°C

28°C

30°C

14

Heating set point (with EKVDX)

24°C

26°C

27°C

28°C

29°C

30°C

31°C

32°C

33°C

35°C

37°C

39°C

41°C

43°C

45°C