Si71-812
Field Setting
Field Setting
85
<Example>
When adjusting the ventilation air flow to low setting in the group setting mode, enter the
mode No., “19” FIRST CODE NO., “0” and SECOND CODE NO., “01”.
Settings and setting numbers
NOTE)
1. The
inside the frame indicates the second code no. set when shipped from factory.
2. The settings are applied to the entire group, but if the mode no. inside the parentheses is
selected, the settings can be applied to individual indoor units.
However, it is only possible to check any changes made to the settings inside the
parentheses in individual mode. (For group batch operation, the changes are made but the
display remains as it was when shipped from the factory.)
3. Do not set anything not shown above. If the applicable functions are not available, they will
not be displayed.
4. When returning to normal mode, the remote controller is initialized, so the display might
show “88.”
Description of setting
Mode
No.
∗
1
FIRST
CORD
NO.
SECOND CORD NO.
01
02
03
04
05
06
07
08
Filter cleaning time setting
NOTE) 5
17
(27)
0
Approx.
2500
hours
Approx.
1250
hours
No
coun-
ting
–
–
–
–
–
Nighttime free cooling
operation setting
(Time after air conditioning
is stopped.)
NOTE) 5
1
OFF
2
hours
later
4
hours
later
6
hours
later
8
hours
later
–
–
–
Fan speed initial setting
4
Normal
Ultra
high
–
–
–
–
–
–
Direct duct connection with
VRV setting
5
Not direct
duct (Air
flow setting)
With direct
duct
(fan off)
–
Not direct
duct (Air
flow setting)
–
With direct
duct
(fan off)
–
–
Setting for cold areas
(Fan operation selection for
heater thermostat OFF)
NOTE) 6
5
Air
flow
setting
Air
flow
setting
–
Fan L
–
Fan L
–
–
Ventilation air flow setting
when Nighttime free
cooling setting
17
(27)
6
High
Ultra
high
–
–
–
–
–
–
ON/OFF input from
Outside (Set when ON/
OFF is to be controlled
from outside)
12
(22)
1
Forced
off
ON/
OFF
control
–
–
–
–
–
–
Power failure automatic
reset (Auto Restart)
12
(22)
5
No
equipped
Equipped
–
–
–
–
–
–
Humidification on/off when
heating thermostat is off
15
(25)
1
No
Yes
–
–
–
–
–
–
Indication of ventilation
mode/Not indication
18
(28)
4
Indication
No
Indication
–
–
–
–
–
–
Fresh up air supply/
exhaust setting
7
No Indication
Indication
–
–
–
–
Supply Exhaust Supply Exhaust
External input terminal
function selection (between
J1 and JC)
NOTE) 7
8
Fresh-up
Overall
alarm
–
–
–
Air flow
increase
–
–
KRP50-2 output switching
selection (between 1 and 3)
9
Fan
on/off
Abnormal
–
–
–
–
–
–
Ventilation air flow setting
19
(29)
0
Low
Low
Low
Low
High
High
Ventilation mode setting
2
Automatic Exchange By-pass
Fresh-up operation
1A
Off
On
–
–
–
–
–
–
Forced fan on
43
Unit no. allocation
45
Description of setting
Mode
No.
∗
1
FIRST
CORD
NO.
SECOND CORD NO.
01 02 03 04 05 06 07 08 09 10 11 12 13
Heating temperature
setting on VKM
°C
14
(24)
1
14 15 16 17 18 19 20 21 22 23 24 25 26
Summary of Contents for VKM100GAMV1
