Test Operation
SiBE37-701
184
Test Operation
3.2Possible settings for function C
The noise of level 3 < level 2 < level 1 (
).
(a) This setting = factory setting
3.3Possible settings for function D and E
For function D (
) only: the noise of level 3 < level 2 < level 1 (
).
For function E (
) only: the power consumption of level 1< level 2 < level 3 (
).
(a) This setting = factory setting
3.4Possible settings for function H
The evaporating temperature level H (high) < level M (medium) < level L (low) (
).
(a) This setting = factory setting
4. Push the
button and the setting is defined.
5. When the
button is pushed again, the operation starts according to the setting.
Refer to the service manual for more details and for other settings.
Confirmation of the set mode
The following items can be confirmed by setting mode 1 (H1P LED is off)
Check the LED indication in the field marked
.
1. Indication of the present operation state
-
h
, normal
-
i
, abnormal
-
j
, under preparation or under test operation
2. Indication of low noise operation state
-
h
standard operation (= factory setting)
-
i
operation
3. Indication of power consumption limitation setting
-
h
standard operation (= factory setting)
-
i
operation
1.2.6.4
Test operation
Do not insert fingers, rods or other objects into the air inlet or outlet. When the fan is
rotating at high speed, it will cause injury.
Do not perform the test operation while working on the indoor units.
When performing the test operation, not only the outdoor unit, but the connected indoor unit will
operate as well. Working on a indoor unit while performing a test operation is dangerous.
H1P H2P H3P H4P H5P H6P H7P
(a)
i
h
h
h
h
h
h
i
h
h
h
h
h
jc
i
h
h
h
h
j
h
i
h
h
h
h
j
j
H1P H2P H3P H4P H5P H6P H7P
i
h
h
h
h
h
j
(a)
i
h
h
h
h
j
h
i
h
h
h
j
h
h
H1P H2P H3P H4P H5P H6P H7P
i
h
h
h
h
h
j
(a)
i
h
h
h
h
j
h
i
h
j
h
h
h
h
1
OFF
1
2
3
L.N.O.P
1
DEMAND
3
1
2
3
L
H
M
L
BS3 RETURN
BS3 RETURN
H1P H2P H3P H4P H5P H6P H7P
h
h
i
h
h
h
h
H1P H2P H3P H4P H5P H6P H7P
h
h
i
h
h
h
h
H1P H2P H3P H4P H5P H6P H7P
h
h
i
h
h
h
h
L.N.O.P
L.N.O.P
DEMAND
DEMAND
Summary of Contents for VRV III REYQ8PY1B
