Dakota Alert DCPT-4000 User Manual Download | Manualshive

Page: 3 / 12

background image

INSTALLING THE BATTERIES

1. Open the transmitter box.

2. Install new CR123A batteries. Make sure that the + and - symbols on the

batteries match the symbols in the compartment.

LOW BATTERY ALERT:

If you hear a second alert after the first alert, and nothing has

activated the transmitter again, the batteries in the transmitter box are low and should

be replaced.

3

«
1
2
3
4
5
...
»

Summary of Contents for DCPT-4000













Reviews:

No comments

Related manuals for DCPT-4000

Brand: K&K Sound Pages: 6

Brand: AstroStart Pages: 2

978 UAT/1090 ES

Brand: SkyGuardTWX Pages: 2

Brand: Vaisala Pages: 4

Brand: V2 Pages: 76

Brand: Jonsa Pages: 12

Brand: M-system Pages: 2

Brand: OrangeRx Pages: 24

Brand: F&F Pages: 12

Brand: Maas Pages: 49

Brand: Advanced Microwave Products Pages: 2

Brand: Siemens Pages: 4

Brand: Siemens Pages: 4

Brand: Siemens Pages: 4

Brand: Siemens Pages: 5

Brand: Siemens Pages: 4

Brand: Siemens Pages: 40

SIMATIC SCP Series

Brand: Siemens Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands