background image

WARRANTY INFORMATION 

Warranty Statement  

Dakota Ultrasonics warrants the 

ZX-1

 against defects in materials and 

workmanship for a period of five years from receipt by the end user.  Additionally, 
Dakota Ultrasonics warrants transducers and accessories against such defects for a 
period of 90 days from receipt by the end user.  If Dakota Ultrasonics receives notice 
of such defects during the warranty period, Dakota Ultrasonics will either, at its 
option, repair or replace products that prove to be defective. 

Should Dakota Ultrasonics be unable to repair or replace the product within a 

reasonable amount of time, the customer's alternative exclusive remedy shall be 
refund of the purchase price upon return of the product. 

Exclusions  

The above warranty shall not apply to defects resulting from: improper or 

inadequate maintenance by the customer; unauthorized modification or misuse;  or 
operation outside the environmental specifications for the product. 

Dakota Ultrasonics makes no other warranty, either express or implied, with 

respect to this product.  Dakota Ultrasonics specifically disclaims any implied 
warranties of merchantability or fitness for a particular purpose.  Some states or 
provinces do not allow limitations on the duration of an implied warranty, so the 
above limitation or exclusion may not apply to you.  However, any implied warranty of 
merchantability or fitness is limited to the five-year duration of this written warranty. 

This warranty gives you specific legal rights, and you may also have other rights 

which may vary from state to state or province to province. 

Obtaining Service During Warranty Period  

If your hardware should fail during the warranty period, contact Dakota 

Ultrasonics and arrange for servicing of the product.  Retain proof of purchase in 
order to obtain warranty service. 

For products that require servicing, Dakota Ultrasonics may use one of the 

following methods: 

- Repair the product
- Replace the product with a re-manufactured unit
- Replace the product with a product of equal or greater performance
- Refund the purchase price.

After the Warranty Period  

If your hardware should fail after the warranty period, contact Dakota Ultrasonics 

for details of the services available, and to arrange for non-warranty service.

 

Distributed by:

 ABQ Industrial LP USA

Tel: 

+1 (281) 516-9292 / (888) 275-5772  

eFax:

 +1 (866) 234-0451

 

Web: 

http

s

://www.abqindustrial.net  

E-mail: 

info@abqindustrial.net

Distributed by:

 ABQ Industrial LP USA

Tel: 

+1 (281) 516-9292 / (888) 275-5772  

eFax:

 +1 (866) 234-0451

 

Web: 

http

s

://www.abqindustrial.net  

E-mail: 

info@abqindustrial.net

Summary of Contents for ZX-1


























Reviews: