background image

Segment Timer Operation

15

Set Program

The segment timer mode includes 7 programs as described below. Program information 

is saved when the All Sport 100 is powered down. 
• 

Programs 1-5

 allow a unique program for each weekday (Monday through Friday).

• 

Program 6

 is a dedicated Play Clock. 

• 

Program 7

 is a dedicated Two-Minute Drill.

Display

Action

CURRENT PROG N*
SELECT 1-7

N = current setting

Press 

<SET PROGRAM •>

 use the number keys to select the 

desired program, and then press 

<ENTER*>

 to accept. 

Once completed, all segments from XX to YY (inclusive) will be 

set to the specified value.

TI-2025 & TI-2026 Segment Timers

The TI-2025 and TI-2026 portable timing displays (

Figure 4

are controllable by an All Sport 100 as well as a wireless 

handheld RC-50 controller. However, before these 

displays may be controlled with the RC-50, they must first 

be programmed with the All Sport 100. Connect the All 

Sport 100 to the display using the provided power/signal 

cable (part # 0A-1196-0095). 
For more information about these displays, refer to the 

TI-2025 & TI-2026 Segment Timers Display Manual (ED-

16738)

, available online at 

www.daktronics.com/manuals

.

Sending Program Information to the Display

Display

Action

TRANSFERING DATA
PLEASE WAIT

TRANSFER
COMPLETE

First ensure the All Sport 100 is properly connected to the TI 

display, and then enter the information for programs 1 to 7. 

When ready to load the program information into the display, 

press 

<ALT>

 followed by 

<SEND>

Wait approximately 5 seconds for the program data to transfer. 

The TI display digits will show “PPPP” if the program data was 

successfully received and stored into the display’s memory. 

The All Sport 100 must then be unplugged to allow the RC-50 to 

control the display remotely. 

DAKTRONICS

Figure 4: 

TI-2025/TI-2026

Summary of Contents for ALL SPORT 100

































Reviews: