Daktronics P1192, Installation Manual

THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS

DRAWING ARE CONFIDENTIAL AND PROPRIETARY.    DO NOT

REPRODUCE BY ANY MEANS WITHOUT THE EXPRESS

WRITTEN CONSENT OF DAKTRONICS, INC.

COPYRIGHT 2015 DAKTRONICS, INC.

DAKTRONICS, INC.

BH

MOUNTING BRACKET

DRILL 1/4" HOLES

REAR

OF

DISPLAY

0'-3"

INSTALLATION PROCEDURE:

1. OPEN THE RIGHT DIGIT AND REMOVE THE COVER FROM THE DRIVER.

2. DRILL A 7/8" HOLE IN THE RIGHT SIDE OF THE DISPLAY PER THE DIMENSIONS SHOWN IN DETAIL A.

3. INSERT INCLUDED CONDUIT CONNECTORS INTO THE 7/8" HOLE AND INTO THE BOTTOM OF THE HORN AS SHOWN IN DETAIL B.

4. POSITION THE HORN MOUNTING BRACKET PER DETAIL B.

5. MARK THE MOUNTING BRACKET HOLE LOCATIONS ONTO THE SIDE OF THE DISPLAY.

6. DRILL 1/4" HOLES WHERE THE MOUNTING BRACKET HOLES WERE MARKED ON THE SIDE OF THE DISPLAY.

7. MOUNT THE HORN MOUNTING BRACKET WITH THE INCLUDED 1/4" HARDWARE.

8. ATTACH THE HORN TO THE BRACKET WITH INCLUDED 1/4" HARDWARE.  *THE WIRES PROTRUDE OUT THE BOTTOM OF THE HORN.  MAKE

SURE THE HORN IS MOUNTED WITH THE BOTTOM DOWN.

9. THE GROUND WIRE WILL NOT BE CONNECTED, CUT THE GREEN WIRE AS SHORT AS POSSIBLE.

10. ROUTE THE WIRES THROUGH THE CONDUIT AND INTO THE DISPLAY.

11. ONCE THE HARNESS HAS BEEN RUN THROUGH THE CONDUIT, CONNECT THE CONDUIT TO THE CONDUIT CONNECTORS IN THE SIDE OF

THE DISPLAY AND THE BOTTOM OF THE HORN.

WIRING INSTRUCTIONS:

1. USE HARNESS 0A-1192-1686 (2-WIRE BLK AND WHT @10' LONG) AND TERMINATE THE BLACK WIRE AND THE WHITE WIRE FROM THIS

HARNESS TO THE TWO WIRES COMING OUT OF THE BOTTOM OF THE HORN. USE THE INCLUDED E-1044 BUTT SPLICES TO MAKE THIS

TERMINATION. NOTE: WIRES FROM THE HORN CAN CONNECT TO EITHER THE BLACK OR WHITE WIRES THIS CONNECTION IS

INTERCHANGEABLE.

2. REFERENCE SCHEMATIC DWG-132173 FOR CONNECTIONS MADE INSIDE DISPLAY TO THE HORN CARD (0P-1192-0399) PROVIDED IN HORN

ASSY KIT.

3. ATTACH THE COVER ONTO THE DRIVER AND ATTACH THE REMOVED DIGIT TO THE DISPLAY FACE.

INSERT CONDUIT

CONNECTORS INTO THE

DISPLAY AND HORN

DRILL 7/8" HOLE

DRAWN:

DATE:

SHEET

JOB NO:

REV

SCOREBOARDS

HORN MTG INSTRUCTIONS; 120V, TI-2003, GYRUS DRIVER

KSCHNABEL

8 MAY 15

P1782

E 10 B

1=5

KSCHNABEL

3054691

00

P1

(DRIVER SHOWN W/O COVER)

J1

J3

J2

(TO TRUMPET HORN)

J5

DRIVER COMPONENTS INSTALLATION PROCEDURE:

1.  FROM THE 0A-1192-1685, HORN INTERFACE CARD ASSY. MOUNT 0P-1192-0399

HORN SWITCH CARD USING HS-1042 SPACER & HC-1238 LOCK NUT.

2.  PLUG TI-2003 HORN SIGNAL HARNESS (0A-1192-0393) PLUG P5 INTO JACK J5 ON

THE DRIVER AND PLUG P2 INTO JACK J2 OF 0P-1192-0399 HORN SWITCH CARD.

3.  PLUG POWER ADAPTER HARNESS 0A-1782-0299 PLUG P42 INTO JACK J42 ON

THE HARNESS LEAVING THE DIGIT DRIVER.

4.  CONNECT PLUG P1 OF THE POWER HARNESS COMING FROM ADAPTER

HARNESS 0A-1782-0299  INTO JACK J1 ON THE HORN INTERFACE CARD.

5.  CONNECT  HORN CABLE PLUG P3 INTO JACK J3 OF THE 0P-1192-0399 AND THE

OPPOSITE END ON TO THE HORN.

SPACER

NUT

P2

STEP 1

STEP 2

J42

J42

STEP 3

STEP 4

STEP 5

NOTES:

-THIS DRAWING DOES NOT DEPICT THE

ACTUAL LAYOUT OF COMPONENTS.

-THIS DRAWING EXPLAINS HOW THE HORN

COMPONENTS ARE CONNECTED TO EACH

OTHER.

GYRUS DIGIT DRIVER