DEUTSCH
*EINSCHALTUNG 2. ZEITSPANNE
Nun muss die zweite Zeitspanne programmiert werden.
Das Verfahren hierzu ist analog und wiederholt sich wie bei EINSCHALTUNG 1. ZEITSPANNE.
Hierbei brauchen nur die Beispielzeit in Start um 15:00 Uhr und in Stop um 22:00 Uhr eingegeben und die Tage Samstag und
Sonntag durch Einstellen auf "ON" aktiviert zu werden.
BEDIENUNGSVERFAHREN:
Taste 6 einmal drücken, es erscheint SET
UHR.
Taste 2 bis "
SET CHRONO
" drücken.
SET
UHR
SET CHRONO
AUSSCHALTUNG DER 1. ZEITSPANNE
Mit den Tasten 4/5 die Uhrzeit “
12:00
”
einstellen, die der Ausschaltzeit der 1.
Zeitspanne entspricht.
Zum Bestätigen und Fortsetzen der
Programmierung Taste 6 drücken,
Taste 3, um zum vorherigen Parameter
zurückzugehen.
STOP PRG1
12:00
CHRONO-AKTIVIERUNG
Taste 6 drücken, es erscheint die
Anzeige
FREIGABE CHRONO
und
OFF
.
Taste 4 drücken, um die
CHRONO
-
Funktion zu aktivieren bzw.
deaktivieren.
ON
wählen.
FREIGABE
CHRONO
ON
TAGE DER 1. ZEITSPANNE AKTIVIEREN
Mit den Tasten 4/5 die Tage aktivieren/
deaktivieren ; mit Taste 2 und 3
durch die einzelnen Tage blättern, es
erscheint der Wochentag, gefolgt von
OFF
.
Für Montag bis Freitag
ON
einstellen,
für Samstag und Sonntag OFF.
MONTAG..PRG1
ON-OFF
Taste 6 zum Bestätigen und Fortsetzen
der Programmierung drücken.
Es erscheint die Anzeige
START PRG1
OFF
.
START PRG1
OFF
WASSERTEMPERATUR-SOLLWERT 1.
ZEITSPANNE
Taste 6 zum Bestätigen und Fortsetzen
der Programmierung drücken.
Mit den Tasten 4/5 die gewünschte
Temperatur für
H2O
einstellen.
(65-80°C)
Zum Bestätigen und Fortfahren Taste 6
drücken.
SET PRG1
75°C
EINSCHALTUNG 1. ZEITSPANNE
Mit den Tasten 4/5 die Uhrzeit “
08:00
”
einstellen, die der Einschaltzeit der 1.
Zeitspanne entspricht.
Zum Bestätigen und Fortsetzen der
Programmierung Taste 6 drücken,
Taste 3, um zum vorherigen Parameter
zurückzugehen.
START PRG1
08:00
EINSCHALTUNG 2. ZEITSPANNE*
Nun muss die zweite Zeitspanne
programmiert werden.
Das Verfahren hierzu ist analog
und wiederholt sich wie bei
EINSCHALTUNG 1. ZEITSPANNE.
START PRG2
OFF
J
WENN DER WOCHENPROGRAMMIERER AKTIVIERT IST, GEHT AUF DER BEDIENTAFEL EIN KLEINES
QUADRAT DES ENTSPRECHENDEN SYMBOLS AN.
PROGRAMMIERBEISPIEL
Nehmen wir nun einmal an, dass wir die Funktion Wochenprogrammierer benutzen wollen und 4 Zeitspannen
folgendermaßen benutzt werden sollen:
1. Zeitspanne: 08:00 bis 12:00 Uhr für alle Wochentage außer Samstag und Sonntag
2. Zeitspanne: 15:00 bis 22:00 nur am Samstag und Sonntag, beide Zeiten mit einem Wassertemperatur-Sollwert von 75 °C
Auf dem Display werden die einzelnen Programmierschritte angezeigt.
134