background image

 30 

 

OPERATION

 

  OBJECT OF THE 

CHECK

 

 

PERIODICITY

 

 

ACTIONS TO TAKE

 

 

REFERENCE  

CHECK

 

 

PRIMARY AND 

SECONDARY AIR 

FANS

 

BEGINNING SEA-

SON

 

check that the fans turn and do not 

cause vibrations, in case remove the 

excess dust and dirt.

 

Fig.3.3.1A-B 

 

GRID HANDLING 

SYSTEM

 

BEGINNING SEA-

SON OR AFTER A 

LONG INACTIVITY 

PERIOD

 

Check for foreign bodies on the slide rod 

and that the end runs correctly function

 

Fig.xx 

ELECTRIC SYS-

TEM

 

BEGINNING SEA-

SON OR AFTER A 

LONG INACTIVITY 

PERIOD

 

Test the differential switch functioning. 

Check connections with the earthing 

system.

 

 

REDUCERS

 

BEGINNING SEA-

SON

 

check the oil level of the reducers from 

appropriate warning light. If the level is 

low, top-up with corresponding oil.

 

Fig.3.3.1A-B 

LUBRICATION  

 

GRID HANDLING 

SYSTEM

 

ONCE A MONTH

 

Clean and grease the slide bar

 

Fig.10.2 

AIR VENTILATION 

PIPES BLADES

 

BEGINNING SEA-

SON OR AFTER A 

LONG INACTIVITY 

PERIOD

 

lubricate the rotary transversal pin of the 

internal blade of the primary and sec-

ondary air pipe using spray oil

 

Fig.7.7 

SCREW PINION   
BEARING

 

BEGINNING SEA-
SON

 

Using a greasing nipple, grease the 
bearing.

 

Fig.3.3.1A-B 

tab.9.2 

9. MAINTENANCE

 

 

9.1 Generality

 

 

The heat generator must be submitted to regular maintenance to guarantee the efficiency of all 

components determining the correct operating of the generator and its main yield. 

Tab. 9.1 

sum-

marises the main operations.  

ATTENTION!! 

BEFORE MAINTENANCE, DISCONNECT THE ELECTRIC ENERGY 

FROM THE GENERATOR BY INTERVENING ON THE MAIN 

SWITCH AND ENSURE THAT THE RESIDUE FUEL INSIDE THE 

FIREBOX IS OFF AND HAS COOLED DOWN

 

 

ATTENTION!! 

MAINTENANCE MUST ONLY BE CARRIED OUT BY QUALIFIED 

STAFF

 

 

9.2 Table of the periodical maintenance operations

 

 

Summary of Contents for CSA100 GM




































Reviews: