DANA SPICER PACCAR 220ev Troubleshooting Manual Download

Page: 13 / 761

General Information

Vehicle System Overview

This section provides a brief overview of the main

systems on the vehicle. More detailed information is

provided in the specific section for each system,

which can be found on the page indicated.

Additional information is also available in the vehicle

service manual.

ESS

… page 19

The Energy Storage System (ESS) is the vehicle

battery pack. It includes the Battery Management

System (BMS) and heating and cooling circuits to

help maintain the proper operating temperature in

cold weather.

Charging System

…

page 161

The charging system converts electrical energy input

to charge the ESS. It can accept either alternating

current (AC) or direct current (DC) input. The

vehicle is charged using a charger that is attached to

the electrical power grid. The charger is referred to

in this manual as an EVSE (Electric Vehicle Supply

Equipment).

Propulsion System

… page 270

The propulsion system converts electrical energy

from the ESS into mechanical energy to propel the

truck. It consists of an electric motor and a Traction

inverter. The propulsion system is available in two

configurations medium duty and heavy duty.

Brake System

… page 325

The brake system is responsible for stopping the

vehicle. The brakes are operated by compressed air

supplied by an onboard compressor.

DCDC System

… page 417

The DCDC system accepts high voltage (HV) input

from the ESS and converts it to 24V low voltage (LV)

to charge the two LV batteries, which power the 12V

and 24V equipment throughout the vehicle.

Low Voltage Distribution System

… page 465

The low voltage distribution system distributes 12V

and 24V power throughout the vehicle to power

onboard equipment and accessories.

Power Steering System

… page 480

The power steering system is an electro-hydraulic

system which produces supplemental steering force

to assist the driver in steering the vehicle.

HVAC System

… page 522

The Heating, Ventilation and Air Conditioning

(HVAC) system provides heating, cooling, and

ventilation to the driver cab.

VCU-HMI System

… page 602

The Vehicle Control Unit (VCU) is the main

processing unit which monitors and controls most of

the systems and equipment on the vehicle. It

interfaces with other equipment either through the

CAN network or by means of dedicated low-voltage

signals. The Human-Machine Interface (HMI)

provides a communication interface between the

VCU and the driver.

Powertrain Cooling System

… page 671

The cooling system helps to maintain the proper

operating temperature for the equipment connected

to the cooling circuit. It consists of a cooling loop,

radiator, pump, and fans.

Telemetry System

… page 690

The telemetry system collects and transmits

operational data from the various vehicle systems to

remote servers where they can be accessed by

operators for monitoring purposes.

ePTO System

… page 700

The electric power take-off (ePTO) system provides

an electrical power output which can be used to

operate aftermarket onboard accessories.

Is a separate vehicle controller that comprises two

major function. That of the supervisory controller,

(FSVCU) where its function is to monitor vehicle

systems on CAN-A, CAN-B, CAN-C, and CAN-D.

Should the selected devices perform an unsafe

function the supervisory controller provides a safe

shutdown sequence. The also functions

as a charge controller, managing the charging

process when the vehicle is connected to an EVSE.

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands

DANA SPICER PACCAR 220ev, Troubleshooting Manual

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands