DANA SPICER PACCAR 220ev Troubleshooting Manual Download

Page: 34 / 761

Troubleshooting

HMI displays or logs

Fault code F0019 and

TMS fault reason 34

Contact Dana for further

investigation.

Is any other system on the

HV DC bus raising an

overvoltage error?

Yes

Does the HMI also display

F0026?

Yes

Refer to the corresponding

error troubleshooting tree.

Disconnect connector RT063

from Battery TMS.

Disconnect connector RT064

from HV junction box.

Check the connectors for

corrosion, scorching, or physical

integrity loss.

With a multimeter, check for continuity between the

following points:

- Continuity : Resistance is less than or equal to 2ohms.

RT063

RT064

Connector pin

RT063

RT064

Is there any evidence of a

continuity loss in the

harness?

Yes

Defective harness.

Replace harness.

Contact Dana for further

investigation.

WARNING:

Electrical hazard.

Follow Safety Warnings and High

Voltage Shutdown Procedures

defined in the Service Manual

and Diagnostic Guide.

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands

DANA SPICER PACCAR 220ev, Troubleshooting Manual

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands