DANA SPICER PACCAR 220ev Troubleshooting Manual Download

Page: 606 / 761

606

Troubleshooting

F0058 - Emergency service cut loop is open.

Error Description

Possible Causes

Possible Solutions

VCU has detected that the cut loop

is broken.

1) Cut loop broken or faulty cut

loop wiring.

2) Cut loop bundle is cut or

damaged.

3) Loss of continuity on cut loop

signal wire (wire cut,

damaged, or 12V fuse F20

blown) AND loss of 12V to

ESS or loss of CAN

communication from ESS to

VCU.

1) Replace cut loop wiring.

2) Troubleshoot specific error.

The cut loop is a section of LV wiring which can

be cut by first responders to shut down the HV

system in an emergency.

If the cut loop is broken:

•

Contactors inside the S-Box will open to

isolate the high voltage battery packs from

the HV distribution system.

•

The VCU will notify the driver immediately

by raising error F0058 and will prohibit

restarting the vehicle.

If error F0058 has been raised, a service reset is

required to clear the error and restart the vehicle.

Attempting to start the vehicle without clearing the

error will raise an additional error message F0108.

A break in the cut loop is also expected to trigger

various other errors including F0016, BMS no

contact, and F0005/F0006/F0007 (fault reason

13).

If a cut loop problem is indicated, the cut loop

should always be inspected before

troubleshooting any other possible root cause.

If the cut loop is intact, the cause of the error may

be a blown fuse or a discontinuity elsewhere in the

wiring.

Connector C40

Connector C91

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands

DANA SPICER PACCAR 220ev, Troubleshooting Manual

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands