DANA SPICER PACCAR 220ev Troubleshooting Manual Download

Page: 97 / 761

Troubleshooting

F0026 (Fault Reason 40, 41, 42, 43)

Error Description

Possible Causes

Possible Solutions

BMS has detected a HV system

isolation fault.

1) Defective charger

2) HV system isolation fault

1) Replace charger

2) Contact Dana

This error indicates that the BMS has detected a HV

system isolation fault. The BMS monitors voltage

and current and raises an error if the calculated

isolation resistance falls below a threshold.

Fault reasons 40, 41, and 42 indicate that the error

occurred while in driving mode. These fault reasons

are numbered in order of increasing severity:

Fault Reason

Isolation Resistance

≤

600

Ω

/V (ohms per volt)

≤

500

Ω/V

(ohms per volt)

≤

400

Ω/V

(ohms per volt)

If fault reason 40 is raised, the high voltage power

and regenerative braking power will both be limited

to 50%. If fault reason 41 is raised, driving will be

disabled. If fault reason 42 is raised, the BMS will

request the vehicle to shut down. In all cases, the

vehicle will not be able to restart until the error is

cleared.

Fault reason 43 indicates that the error occurred

while in charging mode. In this case, the isolation

resistance threshold is 100

Ω/V

. The charging

process will be terminated.

If the error occurred during charging and

subsequently disappears when using a different

charger, it is likely that the error was caused by a

defective charger. The error should still be reported

to Dana.

The VCU independently monitors isolation

resistance and will raise error F0035, F0036, F0037,

or F0038 if a loss of isolation is detected.

In the event of a genuine loss of isolation, both a

BMS error (this error) and a VCU error (F0035,

F0036, F0037, or F0038) are expected to appear. If

F0026 (BMS Fault Reason 40, 41, 42, or 43)

appears alone, the technician should contact Dana

for further investigation.

Warning:

Loss of HV system isolation can

pose an extreme hazard and may result in

high voltage being present in parts of the

vehicle that are not normally energized. Use

extreme caution and report all instances of

this error to Dana.

Summary of Contents for SPICER PACCAR 220ev


























































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands

DANA SPICER PACCAR 220ev, Troubleshooting Manual

Search results

Summary of Contents for SPICER PACCAR 220ev

Reviews:

Related manuals for SPICER PACCAR 220ev

Brands by name

Popular brands