background image

Safety Advice

Attention

In some countries approval is needed to set up a marquee/tent larger than 75 m2. It is your 

responsibility to comply with local rules and regulations and to ensure that the marquee/tent is 

assembled correctly.

In case of bad weather conditions, it is your responsibility to ensure the marquee/tent is safely 

secured and that the marquee/tent does not cause damage to others.

Do not use open fire, welding equipment or other sources which can ignite, inside or close to the 

tent.

The marquee/tent must be safely secured. We recommend you secure your marquee/tent with 

straps and pegs as soon as it is assembled.

Make sure to check if the marquee/tent is covered by your home contents insurance.

Marquees/tents must be evacuated under extreme weather conditions.

In the event of snow, always remove snow from the roof of the marquee/tent regularly to prevent 

snow from building on the roof, as heavy snow can cause the marquee/tent to collapse.

In the event of rain, there is a risk of rain puddles building up on top of the roof of the marquee/

tent. Heavy rain puddles can cause the roof to collapse. It is your responsibility to ensure rain 

puddles do not build up. As a precaution, make sure the roof of the marquee/tent is stretched 

out properly and adequately over the side frames of the marquee/tent and remove rain water 

regularly.

Do not unpack or repack your marquee/tent in freezing temperatures. In case of temperatures 

below zero, always unpack and repack your marquee/tent indoors to avoid the risk of cracking 

parts.

The marquee/tent must be totally dry before you repack and store it to avoid mildew.

Note: 

Marquees are intended for events and other arrangements and are as such only meant for 

short term temporary assembly and the following disassembly. Dancover warranty applies only 

to the normal use of the Product, normal wear and tear excepted, in accordance with written 

use instructions or manual. The warranty does not apply to damage caused by accident, abuse, 

misuse, or modification of the Product.

Warranty Information

Please visit dancovershop.com for information on warranty.

Please always check our website for the latest safety advice and manual.

Summary of Contents for Titanium Tent

















Reviews: