background image

1.

 Determine the desired height of the latch on the gate. Hold the latch in place on 

the post and close the gate.

2.

 Position the Striker Body “C” on the gate frame by engaging the striker bolt 

into the latching tongue. (Check whether the adaptor shim ‘S

3

’ needs to be 

applied to fit your gate frame.) When all latch 

components are aligned correctly, use the pencil to mark inside the four fixing 

slots of the Striker Body “C”. 

3.

 

Place all latch components aside and drill a pilot hole in the center of the 

marked slots using a 

11

/

64

" (4.5mm) d

rill-bit. Remember that centering the 

screws inside the slots allows future adjustment for gate sag.

4.

 Secure the Striker Body “C” firmly onto the gate frame using four of the large 

hex-head Tek screws supplied.

5.

 Open the gate. Place the Latch Assembly back onto the latch post and then close 

the gate. Engage the Striker Bolt through the latch tongue again, aligning the main 

Latch Body on the latch post so that the Striker Bolt will close in the center of the latch 

tongue (the Rivet marks the center of the latching zone).

6.

 Hold the Latch Assembly in place and mark the post through the two main screw-

fixing holes at the side of the Round Post Bracket.

INSTALLING THE

ROUND POST BRACKET

Once the “handing” is determined, 

insert the Round Post Bracket into 

the back of the latch body at a 

slight angle, as shown: rotate the 

Post Bracket in the direction of 

the arrows until it snaps firmly in 

alignment on the latch body. Insert 

a single short screw (Screw 1) in the 

center hole inside the bracket, and  

a short screw top and bottom  

(screws 2 & 3) of the latch.

Round Post 

Bracket

Key

Tongue

FENCE

POST

GATE

FRAME

LATCH

BODY

STRIKER

BODY

Striker 

Bolt

Release

Knob

Round Post 

Bracket

A

INSTALLATION PROCEDURE

• This latch is designed to be fitted to the “opening” side of the gate. See 

notes at right re right- or left-hand installation, and also for the fitting of the 

Round Post Bracket (A) to the Latch Body  

➧ ➧ ➧

Post sizes: 1

7

/

8

–2", 2

3

/

8

", 2

7

/

8

" (48–51mm, 60mm, 73mm).  

Gate frame sizes: 1

3

/

8

" and 1

5

/

8

" (35mm and 41mm).

Gap Variance: 1" -2

1

/

4

" (25mm - 57mm)

Tools: Electric or cordless drill (use low clutch settings), Phillips No.1 

screwdriver, 

5

/

16

" hex-head (Tek) drill drive (for use in electric/cordless drill), 

11

/

64

" [4.5mm] drillbit for pre-drilling metal.

A

B

B

S

1

S

2

C

INSTALLATION NOTES & PROCEDURE

• This latch is designed, ideally, to be fitted to the inside (i.e. house or tennis court side) of the gate. If 
installing to the outside (i.e. street side) of the gate ensure there is hand access to operate the latch…or, if 
this pack contains an “EXTERNAL ACCESS KIT”, ensure it is fixed to this latch before installing the entire latch 
onto the gate (see over for details).
• For 2

3

/

8

" (51mm) fence posts and 1

5

/

8

" (41mm) gate frames, no adapters are required.

This latch kit includes special adapter shims for fitting the latch to posts and gate frames of varying diameters (see S1, S2 
& S3).  The adapters have the diameter they are designed for molded into them.  If required, place two identical adapters 
(S1 or S2) into their corresponding positions on the inside the Round Post Bracket facing the Fence Post.

For LokkLatch only installation , follow Step #1 

STEP #1 — MAIN LATCH BODY

Rivet

S

3

S

1

S

2

Latch Body

Screw 1

Screw 2

Screw 3

7.

 

Remove the Latch Assembly and drill the pilot holes where marked.

8.

 

Secure the Latch Assembly using the two remaining hex-head Tek screws supplied.

9.

 Check latch operation to ensure smooth, reliable latching. Your LOKKLATCH is now ready for use. 

NB:

 If this pack does not have an “External Access Kit”, you can purchase one from your supplier.

STEP #2 — EXTERNAL ACCESS KIT

For latch with External Access Kit , follow Step #1, then Step #2

For a downloadable Adobe Acrobat (.PDF) version of our Limited LIFETIME WARRANTY,  

go to our website at www.ddtechglobal.com

LLINSTR0028PA       •instr_LLABRND_1 11 11

(

Note:

 Locking the External Access Assembly only locks the Push Button. It does not lock the Latch Body, which is lockable separately.)

RIVET

Horizontal

Locate

Push Rod

into hole

Fixing

Shroud

Push Button

housing

Release 

Knob

Release 

Knob

Push rod

Large return

Small 

return

The External Access Kit (EAK) allows a gate to be  

opened and locked from the opposite side to the latch.   

The EAK is connected to the Latch Body by a Push Rod.

INSTALLATION PROCEDURE

1.

 With the latch in the unlocked position, prop the gate  

open.  Slide the Release Knob to the up position at the  

rear of the Latch Body.  Take the Push Rod and, holding  

it vertically, slide the Large Return through the slot in the  

side of the Latch Body as shown in diagram 1.  Be sure the Large Return  

protrudes completely through to the other side of the Latch Body.

2.

 Lower the Release Knob to the down position so that it encloses the Large  

Return of the Push Rod.  Turn the key to lock the Release Knob in place.   

Rotate the Push Rod to the horizontal position as shown in diagram 2.

3.

 To aid with installation, the Push Button is locked.  Place the Push Button Assembly  

against the opposite side of the Round Post Bracket from the Latch Body.  

Place the Small Return of the Push Rod into the hole on the side of the  

Push Button as shown in diagrams 3 & 4.  

4.

 With the Small Return of the Push Rod firmly inside the hole on the Push  

Button, slide the Fixing Shroud over the Push Button until the Fixing Shroud  

sits firmly into the corresponding Round Post Bracket molding (see diagram 5).  

This will leave the Push Rod at a slight angle, which is normal. 

5.

 Secure the Fixing Shroud to the Round Post Bracket with the four small screws  

using the Phillips No. 1 screwdriver.  Unlock the Push Button and check for smooth  

operation.  The External Access Kit is now ready for use.

FOR ROUND POST AND GATE FRAME 

®

www.ddtechglobal.com

AUSTRALIA:

 Unit 6, 4-6 Aquatic Dr, Frenchs Forest NSW 2086

USA:

 7731 Woodwind Drive, Huntington Beach, CA 92647

Reviews: