background image

  

12  

July 31, 2019 

 

D & R Electronics warrants its new products to be free from defects in material and workman-
ship, under normal use and service for a period of three years on parts replacement. 
This warranty applies only to original purchasers acquiring the product directly from D&R 
Electronics, or its authorized dealers. Warranty will not be recognized without proof of  
purchase or bill of sale. 
This warranty is not transferable. 
The warranty begins on the date of delivery to the first user/purchaser. 
This warranty shall not apply to products which must be repaired due to normal wear and tear, 
negligence, improper installation, abuse, misuse, or which have been altered or modified at a 
facility other than D & R Electronics, or its authorized depot centers. 
Units proved to be defective within the warranty period, based on an examination by D&R 
Electronics, will be replaced or repaired at D & R Electronics’ option. This warranty does not 
cover travel expenses or labor charges for removal or installation.  
Lamps, flash tubes, batteries or other items considered consumables are not covered under 
warranty. 
This warranty is in lieu of all other express warranties. D&R Electronics makes no warranties, 
expressed or implied, other than the express warranties contained herein. 

WARRANTY 

PRODUCT RETURN POLICY 

In order to provide you with faster service, product returns for repair or replacement, must 

have a 

Return Goods Authorization Number (RGA number)

. Please contact our company to 

obtain a RGA number before you return the product to D & R ELECTRONICS. Write the RGA 
number clearly on the exterior of the package. Be sure you use sufficient packing materials to 
avoid damage to the product being returned while in transit. 
D & R ELECTRONICS assumes no responsibility or liability for expenses incurred for the  

removal and/or the installation of products requiring service and/or repair. Repairing or  
replacing product is at the discretion of D & R ELECTRONICS.  

CANADA 
8820 George Bolton Pkwy. 
Bolton, Ontario L7E 2Y4 
Tel: (905) 951-9997 
Fax: (905) 951-0019 
 
 
 

 
 

USA 

2299 Kenmore Avenue  

Building 3, Doors 11-14 

Buffalo, New York 14207          

Toll Free: 1-800-538-7338 

                                                                                                                             

www.dandrelectronics.com 

D&R ELECTRONICS Co. LTD. 

Summary of Contents for F5S-IQ Series













Reviews: