Operator's Manual for DM100
VDR
and DM100 S-VDR G2
Copyright Danelec Marine A/S
8
Error
codes
Error codes and messages will be displayed by the BCP.
8.1
Error
codes
004
[SYSTEM
The VDR has encountered an unrecoverable system error. Reboot
PATALLERROR
the
system.
If
the
error
persists, the
most
probable cause is
a
defective CPU
board
or defective system RAM
036
|CONFIG
The VDR was
unable
to save
the
configuration. Please retry. This
Drsble fosaavs
error
is
only expected to occur during configuration (installation)
of
the system
042
|CONFIG
:
:
The
VDR
is
unable to find any configuration at all. Replace
the
Configuration
failed
|
ompact
flash
in the DPU (a properly made boot flash contains a
default configuration from which the system can start). Restore
a
backup
of
the
configuration.
054
|PBSU
The system
is
running on battery. Both
the
main
power
and
the
Runnings
ombattory
emergency
power
are
absent.
If
there
is
a general
power
failure
on
the vessel, ignore this message; otherwise check the
power
supply
in the DAU. Consult section 3.2 for details.
056
|AUDIO
)
The microphone test failed. Force a
microphone
test
(this
is
a
Microphones
failed
feature on
the
BCP).
This
test
will reveal which microphone
is
causing the problem. Check
that
the “BMU active” checkbox
is
unchecked for non-existing microphones. Check
the
cable for
microphones)
reported as faulty. Test the inputs on
the
audio
interface module with a spare microphone. Replace microphones
which are reported faulty
if
no other
error
is
discovered.
058
|AUDIO
;
:
One
or
more microphones are using too much power. The cabling
Power
short
circuit
|,nq
microphones
must
be checked.
060
|STATUS
The system
is
not
receiving UTC from the GPS. Check
that
GPS
DIE
timeout
is
on. Check the signal from
the
GPS (use serial
monitor
in VDR
explorer, WEB status
or
VGA status display).
If
no
signal
is
present check the cable. Otherwise check
that the
configuration
has been done correctly.
UTC time from the GPS has changed
unexpectedly
(at least two
hours) from current system time and is
not
accepted for VDR
Gio
be
Rui
sync. Check that
the
UTC time
of
the VDR matches the UTC you
062
jumped
(go
to
menu)
would expect, using an external time
source.
If
not
inspect the data
on the configured UTC
port
to make sure
that
it
is
indicating the
correct UTC.
If
the
UTC time from the
GPS
is
correct; you can
accept its value and
clear
this
alert from
the
BCP menu.
UTC from the GPS differs by more than
2
seconds from current
DR
not synchronized
system time. The
VDR
will synchronize within
2 minutes,
if
the
063
|
io ure
time
from
cps
|
UTC differs by less than
2
hours from the system time.
If
UTC
time
of
GPS
is
correct; you can
accept
its
value and
clear
this
alert
from the BCP menu.
070
|BSU
.
)
The communication between the
power
supply circuit and
the
Communication
failed
|,ain
CPU in the DPU has been interrupted.
If
the
error
persists,
DBS11011-20
Page 21/31
rrrTETETIRRETITREERIEITIMIMIMI
EME
NNN
REM
E
NM
NNMNM
mM
