Danfoss ADAP-KOOL AK-CT 200A User Manual Download

Page: 28 / 40

User

Guide RS8GR602 © Danfoss 2016-10

AK-CT

450A

Fan pause while night blind rolls down

Here you can set the fan pause time, so the night blind can roll down unhindered

to the correct position.

P65

BlindFanStop

Max. on time for light after manual DI activation

Delay time before light goes off again after light has been turn on manual due to

product stocking.

P66

Light On Time

Case shutdown

Service

Temperature measured with S5 sensor

u09

S5 temp.

Status on DI1 input. on/1=closed

u10

DI1 status

Read the duration of the ongoing defrost or the duration of the last completed

defrost.

u11

Defrost time

Temperature measured with S3 sensor

u12

S3 air temp

Status at the day-/night operation (night operation: on/off)

u13

Night Cond.

Temperature measured with S4 sensor

u16

S4 air temp

Thermostat temperature

u17

Ther. air

Read the ongoing cutin time for the thermostat or the duration of the last

completed cutin

u18

Ther runtime

Read the valve’s actual opening degree

u23

Valve OD %

Read the temperature at the S6 sensor

u36

S6 temp

Status on DI2 input. on/1=closed

u37

DI2 status

Air temperature. Weighted S3 + S4

u56

Display air

Measured temperature for alarm thermostat

u57

Alarm air

* Status on relay for cooling

u58

Comp1/LLSV

Status on relay for fan

u59

Fan relay

* Status on relay for defrost

u60

Def. relay

Status on relay for railheat

u61

Railh. relay

* Status on relay for alarm

u62

Alarm relay

Status on relay for light

u63

Light relay

* Status on relay for hot gas valve

u64

SuctionValve

* Status on relay for compressor 2

u67

Comp2 relay

* Temperature measured with S5B sensor

u75

S5 temp. B

* Temperature measured with S3B sensor

u76

S3 air temp B

* Temperature measured with S6B sensor

u79

S6 temp. B

* Status on relay for hot gas

u80

Hotgas valve

* Status on relay for heating element in drip tray

u81

Drip tray

* Status on relay for night blinds

u82

Blinds relay

* Status on relay for defrost 2

u83

Def. relay 2

* Readout of the actual rail heat effect in %

u85

Rail DutyC %

Readout of which thermostat used for regulation: 1= Thermostat 1,

2= Thermostat 2

u86

Ther. band

Status on input DI3 (closed / open)

u87

DI3 status

Readout of the actual cutin value for the thermostat

u90

Cutin temp.

Readout of the actual cut out value for the thermostat

u91

Cutout temp.

* Measured temperature for alarm thermostat for B section

U34

Alarm air B

* Air temperature. Weighted S3 + S4 temp. for B section

U35

Display air B

* Status of relay for light 2

U36

Extra light

* Status of relay for ECO fan

U37

Fan Eco

* Status of relay for defrost 3

U38

Def. relay 3

Status of DI4 input. On=closed

U39

DI4 status

Status of DI5 input. On=closed

U40

DI5 status

Status of DI6 input. On=closed

U41

DI6 status

Status of high-voltage input DI7, 230 V = 1 = closed

U42

DI7 status

Status of high voltage input DI8, 230 V = 1 = closed

U43

DI8 status

0-10 V output indicates EVR valve’s degree of opening

U44

AO1 voltage

Summary of Contents for ADAP-KOOL AK-CT 200A









































Search results

Summary of Contents for ADAP-KOOL AK-CT 200A

Reviews:

Related manuals for ADAP-KOOL AK-CT 200A

Brands by name

Popular brands

Danfoss ADAP-KOOL AK-CT 200A, User Manual

Search results

Summary of Contents for ADAP-KOOL AK-CT 200A

Reviews:

Related manuals for ADAP-KOOL AK-CT 200A

Brands by name

Popular brands