User manual
iSave 21
10
180R9221 / 521B1174 / DKCFN.PS.003.A1.02
3.4 Preferred system design
Danfoss recommends building systems with a high degree of safety. The PI&D in chapter
5.16 shows the Danfoss preferred system design.
• It is always the system builders’ responsibility that the system design does not cause any
form of hazard and are adapted to local regulations.
• Proper installation and care of shutdown devices and over-pressure protection equip
-
ment is essential.
4.1 Arrival inspection
The iSave is packed in a wood container with plugs in the port connections to protect the
unit from damage during transport.
Remove all packing materials immediately after delivery. Immediately check the shipment
for damage on arrival and make sure that the name plate/type designation is in accordance
with the packing slip and your order.
In case of damage and/or missing parts, a report should be drawn up and presented to the
carrier at once.
The identification label on the iSave states the specific type, the serial number and the code
number of the iSave; see fig. below.
The last three digits of the Serial No. indicate the week and year of production.
4.2 Return to the supplier
Flush the iSave with clean water. Drain the iSave and plug the port connections with a cap/cover.
Pack the iSave into a suitable container and make sure that it is suitably fastened to the
container.
Please contact your local authorised distributor or:
Danfoss A/S
DK-6430 Nordborg,
Denmark
Telephone: +45 7488 2222
Fax:
+45 7445 3831
Email: ro-solutions@danfoss.com
Homepage: www.ro-solutions.com
4.3 Handling
• Personnel involved in lifting and transportation of the equipment must be trained in
proper handling and safety procedures.
• Observe the local regulations regarding lifting.
• Use suitable, permitted lifting equipment.
• The iSave (set) could slip the lifting arrangement.
• Be aware of individuals located in the operation area while lifting the component.
4. Arrival inspection, handling and storage
Summary of Contents for iSave 21
