8-13 Configurable Status Word STW
Option:
Function:
[71] Logic Rule 1
See parameter group
13-4* Logic Rules
. If
Logic Rule 1 is evaluated as TRUE, the
output goes high. Otherwise, it is low.
[72] Logic Rule 2
See parameter group
13-4* Logic Rules
. If
Logic Rule 2 is evaluated as TRUE, the
output goes high. Otherwise, it is low.
[73] Logic Rule 3
See parameter group
13-4* Logic Rules
. If
Logic Rule 3 is evaluated as TRUE, the
output goes high. Otherwise, it is low.
[74] Logic Rule 4
See parameter group
13-4* Logic Rules
. If
Logic Rule 4 is evaluated as TRUE, the
output goes high. Otherwise, it is low.
[75] Logic Rule 5
See parameter group
13-4* Logic Rules
. If
Logic Rule 5 is evaluated as TRUE, the
output goes high. Otherwise, it is low.
[80] SL Digital
Output A
See
13-52 SL Controller Action
. The output
goes high whenever the Smart Logic
Action
[38] Set digital out A high
is
executed. The output goes low whenever
the Smart Logic Action
[32] Set digital out
A low
is executed.
[81] SL Digital
Output B
See
13-52 SL Controller Action
. The input
goes high whenever the Smart Logic
Action
[39] Set digital out B high
is
executed. The input goes low whenever
the Smart Logic Action
[33] Set digital out
B low
is executed.
[82] SL Digital
Output C
See
13-52 SL Controller Action
. The input
goes high whenever the Smart Logic
Action
[40] Set digital out C high
is
executed. The input goes low whenever
the Smart Logic Action
[34] Set digital out
C low
is executed.
[83] SL Digital
Output D
See
13-52 SL Controller Action
. The input
goes high whenever the Smart Logic
Action
[41] Set digital out D high
is
executed. The input goes low whenever
the Smart Logic Action
[35] Set digital out
D low
is executed.
[84] SL Digital
Output E
See
13-52 SL Controller Action
. The input
goes high whenever the Smart Logic
Action
[42] Set digital out E high
is
executed. The input goes low whenever
the Smart Logic Action
[36] Set digital out
E low
is executed.
[85] SL Digital
Output F
See
13-52 SL Controller Action
. The input
goes high whenever the Smart Logic
Action
[43] Set digital out F high
is
executed. The input goes low whenever
the Smart Logic Action
[37] Set digital out
F low
is executed.
8-14 Configurable Control Word CTW
Option:
Function:
Selection of control word bit 10, if it is active
low or active high.
[0] None
[1] Profile default
[2] CTW Valid,
active low
[3] Safe Option
Reset
[4] PID error
inverse
When enabled, it inverts the resulting error
from the process PID controller. Available
only if "Configuration Mode" is set to "Surface
Winder", "Extended PID Speed OL" or
"Extended PID Speed CL".
[5] PID reset I
part
When enabled, resets the I-part of the Process
PID controller. Equivalent to
7-40 Process PID
I-part Reset
. Available only if "Configuration
Mode" is set to "Surface Winder", "Extended
PID Speed OL" or "Extended PID Speed CL".
[6] PID enable
When enabled, enables the extended process
PID controller. Equivalent to
7-50 Process PID
Extended PID
. Available only if "Configuration
Mode" is set "Extended PID Speed OL" or
"Extended PID Speed CL".
8-50 Coasting Select
Option:
Function:
Select control of the coasting function via the
terminals (digital input) and/or via the bus.
[0] Digital
input
Activates Start command via a digital input.
[1] Bus
Activates Start command via the serial
communication port or fieldbus option.
[2] Logic AND Activates Start command via the fieldbus/serial
communication port, AND additionally via one
of the digital inputs.
[3] Logic OR
Activates Start command via the fieldbus/serial
communication port OR via one of the digital
inputs.
8-51 Quick Stop Select
Select control of the Quick Stop function via the terminals
(digital input) and/or via the bus.
Option:
Function:
[0]
Digital input
[1]
Bus
[2]
Logic AND
[3]
Logic OR
Parameters
MCA 122 Modbus TCP
MG90P202 - VLT
®
is a protected Danfoss trademark
29
5
5
