User Guide
MES 1003 WMS
Doc no. 100837-MAN – Rev. E1 – Rev. date 2022-10
© Danfoss IXA A/S | Page 23
3.
Logging
The sensor logs measurements, events, warnings and alarms. As a minimum, each line in the log is given a time-stamped
starting date, hours, minutes, seconds and a description of the measurement/event/warning/ alarm. The log is available
for at least the last 18 months, depending on logging intervals. Refer to section 2.4.1 – Diagnostics Report and section
2.4.5 – Measurement Log for procedures on how to download log files.
3.1.
Example of Measurement Log
The data in Table 9 is the result of a measurement log generated as a csv file.
D
a
te
T
im
e
S
a
m
p
le
P
o
in
t
C
o
rr
e
ct
e
d
P
A
H
T
u
rb
id
it
y
p
H
S
y
st
e
m
t
e
m
p
.
T
e
m
p
.
R
a
w
P
A
H
T
e
m
p
e
ra
tu
re
S
P
1
T
e
m
p
e
ra
tu
re
S
P
2
T
e
m
p
e
ra
tu
re
S
P
3
T
e
m
p
e
ra
tu
re
S
P
4
P
re
ss
u
re
S
P
1
P
re
ss
u
re
S
P
2
P
re
ss
u
re
S
P
3
P
re
ss
u
re
S
P
4
F
lo
w
S
w
it
ch
S
ta
te
2019.06.19
14:02:00
1
5.8
152.4
6.9
50.5
25.1
32.5
15.6
19.8
9999
9999
112.2
110.8
9999
9999
1
2
2019.06.19
14:03:00
2
47.4
159.7
6.5
50.5
25.4
280.9
15.6
19.8
9999
9999
111.8
111.2
9999
9999
1
2
2019.06.19
14:04:00
1
5.2
151.9
6.9
50.6
25.2
31.8
15.6
19.7
9999
9999
112.1
110.6
9999
9999
1
2
2019.06.19
14:05:00
2
48.6
160.4
6.6
50.6
25.3
295.6
15.6
19.8
9999
9999
112.0
110.9
9999
9999
1
2
2019.06.19
14:06:00
1
5.1
151.6
6.9
50.5
25.2
31.2
15.6
19.7
9999
9999
111-9
111.1
9999
9999
1
2
Table 9: Example of Measurement Log
Column name
Description
Date
Measurement date
Time
Measurement time
Sample Point
Which sample point is being measured:
1 = Sample point 1
2 = Sample point 2
3 = Sample point 3 (optional)
4 = Sample point 4 (optional)
Corrected PAH
Corrected PAH value (turbidity and phenanthrene equivalent)
Turbidity
Measured value for turbidity
pH
Measured value for pH
System temperature
Temperature of the controller
Temperature
Measured temperature (with pH sensor)
Raw PAH
Output from PAH Sensor
Temperature WSU 1
Sample water temperature in sample point 1 in
℃
Temperature WSU 2
Sample water temperature in sample point 2 in
℃
Temperature WSU 3
Sample water temperature in sample point 3 in
℃
(optional)
Temperature WSU 4
Sample water temperature in sample point 4 in
℃
(optional)
Pressure WSU 1
Pressure before sample pump in WSU 1 in mbar(g)
Pressure WSU 2
Pressure before sample pump in WSU 2 in mbar(g)
Pressure WSU 3
Pressure before sample pump in WSU 3 in mbar(g) (optional)
Pressure WSU 4
Pressure before sample pump in WSU 4 in mbar(g) (optional)
Flow switch
Indicates flow switch state:
0
= Off (low flow)
1
= On (sufficient flow)
State
Indicates operational mode:
0
(standby)
1
(starting)
2
(sensing)
3
(stopping)
4
(disconnected)
Table 10: Legend to Table 9
