background image

Type label

The CS100 type label is located on the side of the enclosure.

CS100 type label information

Model

Part number

Serial number

E-mark certification number

CE Mark

Country of Origin

Traceability code in data matrix code

C

Caution

The device type label contains important information and should not be removed. Solvents can destroy
the label imprint.
Do not contact the type label with any solvent-containing substance.

Intended use

W

Warning

Danger due to possibility of deficient data transmissions. This device operates using radio signals and
cellular networks.
Do not us this device for safety-related applications.

Insufficient mobile radio network availability, interference, failure or malfunction of the device may lead
to faulty data transmission. Because of this, data transmission cannot be guaranteed always and under all
conditions.

Do not operate the device in machines and applications where life depends on the proper (fault-free)
operation of this device.

Never rely solely on wireless device for essential communications, the CS100 is not designed for
safety related applications.

This device is designed to be used in systems which must be checked for conformity with legal
requirements prior to placing into operation.

Only qualified technicians and electricians with advanced knowledge of electrical engineering and
fieldbus systems should put this device into operation. The integrator of this device is responsible to
check and comply with regional directives and requirements.

The device can be used in environments that require protection class IP69k.

IP69k protection is only ensured if all connectors are plugged in or covered with suitable protection
caps.

Before exposing the device to dust and water, plug in all connectors.

Do not immerse the device in water or other liquids.

The OEM of a machine or vehicle in which PLUS+1

®

 or others electronic controls are installed has the full

responsibility for all consequences that may occur.

Technical Information

PLUS+1 Connect CS100 IoT Gateway — Professional Install Only

Device elements

 

©

 Danfoss | October 2020

BC299456869228en-000101 | 7

Summary of Contents for PLUS+1 Connect CS100

























Reviews: