background image

Application guidelines

30

FRCC.PC.021.A5.22

CAN-Bus and Modbus RS485 Communication

General hardware network and 

communication protocol

Dipswitches

Compressor address set-up 

for CAN-Bus and Modbus

CAN-Bus and RS485 hardware network must 
follow the recommendations described in the 
document DKRCC.PS.RIO.F1.02.

CAN-Bus and Modbus RS485 Communication 
protocol parameters are as follow:
a. CANOPEN: nodeID: 1, baudrate: 50K

b. Modbus RS485: ID: none, baudrate: 9600, 
databits: 8, partity: NONE, stop bits: 1. 

Dipswitches on OCS are set at 0 by default 
and have to be changed following the 
recommendation below:
Before changing the compressor address on 
dipswitches, the OCS must be powered-off.
A valid NodeID has to be set as binary code. 

The 4 first dipswitches (1 to 4) are for compressor 
identifiant, the 3 last dipswitches (5 to 7) are for 
circuit/rack identification. 
Below tables give examples.
The dipswitch address is read as NodeID at 
power-up and changed if address is valid (1 to 
125).

Compressor NodeID must be changed to have 
individual address. There are two ways to change 
the compressor address:

•  Dipswitches on OCS (recommended).
•  NodeID from MMIMYK 

Dipswitches on OCS

address

Compressor

Circuit

1

2

3

4

5

6

7

8

default

Example 1: 1 circuit, 3 compressors 
Compressor 1

1

1

Compressor 2

1

2

Compressor 3

1

1

3

Example 2: 2 circuits, 2 compressors per circuit
Compressor 1

 Circuit A

1

1

17

Compressor 2

 Circuit A

1

1

18

Compressor 1

 Circuit B

1

1

33

Compressor 2

 Circuit B

1

1

34

Example 3: 2 circuits, 3 compressors per circuit
Compressor 1

 Circuit A

1

1

17

Compressor 2

 Circuit A

1

1

18

Compressor 3

 Circuit A

1

1

1

19

Compressor 1

 Circuit B

1

1

33

Compressor 2

 Circuit B

1

1

34

Compressor 3

 Circuit B

1

1

1

35

Summary of Contents for PSH051-4





























































Reviews: