background image

10

What is a programmer?

... an explanation for householders.

Programmers allow you to set ‘On’ and ‘Off’ time periods. 
Some models switch the central heating and domestic 
hot water on and off at the same time, while others allow 
the domestic hot water and heating to come on and go 
off at different times.

Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. 
On some programmers you must also set whether you 
want the heating and hot water to run continuously, run 
under the chosen ‘On’ and ‘Off’ heating periods, or be 
permanently off.

The time on the programmer must be correct. Some 
types have to be adjusted in spring and autumn at the 
changes between Greenwich Mean Time and British 
Summer Time.

You may be able to temporarily adjust the heating 
programme, for example, ‘Override’, ‘Advance’ or ‘Boost’. 
These are explained in the manufacturer’s instructions.

The heating will not work if the room thermostat has 
switched the heating off. And, if you have a hot-water 
cylinder, the water heating will not work if the cylinder 
thermostat detects that the hot water has reached the 
correct temperature.

The text below has been edited and approved by the 

Plain English Campaign, who has issued a Crystal Mark 

to be displayed with it.

What is a programmer?

Summary of Contents for SET2E

















Reviews: