PENGUIN REFRIGERATION LTD
Unit
T:
Page
Registered in England
The
easy fault finding.
start or stops.
Start by Linking out the Thermostat
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
Connect the LED faul
If a
control box
compressor refuses to start.
Interpreting
1 Flash
There is insufficient voltage reaching the fridge compressor.
PENGUIN REFRIGERATION LTD
Unit 2b
Alexandria Park
T: 02392 453293
Page 1
Registered in England
The Danfoss BD35 and BD50 compressors have their own fault diagnostic allowing
easy fault finding.
start or stops.
Start by Linking out the Thermostat
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
Connect the LED faul
If an LED light is
control box
compressor refuses to start.
Hint:
An electrical multi meter can be
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
a signal.
Interpreting
1 Flash
There is insufficient voltage reaching the fridge compressor.
PENGUIN REFRIGERATION LTD
Alexandria Park
Penner
02392 453293
F: 02392 453293
Registered in England
No: 4310267
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
easy fault finding.
start or stops.
Start by Linking out the Thermostat
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
Connect the LED faul
light is connected between the
control box, as shown in the diagram above
compressor refuses to start.
Hint:
An electrical multi meter can be
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
a signal.
Interpreting the results
Low Voltage
There is insufficient voltage reaching the fridge compressor.
PENGUIN REFRIGERATION LTD
Penner Road
Havant
02392 453293
E: sales@penguinfrigo.co.uk
No: 4310267
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
The fault code will only be shown when
Start by Linking out the Thermostat
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
Connect the LED fault diagnosis curcuit
connected between the
as shown in the diagram above
compressor refuses to start.
An electrical multi meter can be
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
results
Low Voltage
There is insufficient voltage reaching the fridge compressor.
PENGUIN REFRIGERATION LTD
Havant
Hants
E: sales@penguinfrigo.co.uk
No: 4310267
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
The fault code will only be shown when
Start by Linking out the Thermostat
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
t diagnosis curcuit
connected between the
as shown in the diagram above
An electrical multi meter can be
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
There is insufficient voltage reaching the fridge compressor.
Hants
PO9 1QY
E: sales@penguinfrigo.co.uk
Suppliers of
No: 4310267
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
The fault code will only be shown when
Start by Linking out the Thermostat
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
t diagnosis curcuit
connected between the small positive
as shown in the diagram above
An electrical multi meter can be used instead of an LED. Set the meter to
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
There is insufficient voltage reaching the fridge compressor.
Suppliers of
No: 4310267
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
The fault code will only be shown when
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
small positive
as shown in the diagram above, it will flash an error code if the
used instead of an LED. Set the meter to
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
There is insufficient voltage reaching the fridge compressor.
No: 4310267
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
The fault code will only be shown when the compressor fails to
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
small positive (+) and
it will flash an error code if the
used instead of an LED. Set the meter to
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
There is insufficient voltage reaching the fridge compressor.
VAT No: GB 785 5650 85
Danfoss BD 35 and 50F Fault Diagnostic.
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
the compressor fails to
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
and D
terminal
it will flash an error code if the
used instead of an LED. Set the meter to
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
VAT No: GB 785 5650 85
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
the compressor fails to
To ensure the thermostat is not causing problems put a link out between C and T
terminals this will force the compressor to run continually during testing.
terminal on the
it will flash an error code if the
used instead of an LED. Set the meter to
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
VAT No: GB 785 5650 85
anfoss BD35 and BD50 compressors have their own fault diagnostic allowing
the compressor fails to
To ensure the thermostat is not causing problems put a link out between C and T
the
it will flash an error code if the
used instead of an LED. Set the meter to
continuity (will also have a beep alarm when continuity is made). Put the
probes on the small + and the D terminal and the meter will sound or show
