Parameter 2-02 DC Braking Time
x
x
x
x
Parameter 2-04 DC Brake Cut In Speed [Hz]
x
x
x
x
Parameter 2-06 Parking Current
x
x
x
Parameter 2-07 Parking Time
x
x
x
Parameter 2-10 Brake Function
x
x
x
x
Parameter 2-16 AC brake Max. Current
x
Parameter 2-17 Over-voltage Control
x
x
x
x
Parameter 4-10 Motor Speed Direction
x
x
x
x
Parameter 4-14 Motor Speed High Limit [Hz]
x
x
x
x
Parameter 4-18 Current Limit
x
x
x
x
Parameter 4-19 Max Output Frequency
x
x
x
x
Parameter 4-58 Missing Motor Phase Function
x
x
x
x
Parameter 14-01 Switching Frequency
x
x
x
x
Parameter 14-03 Overmodulation
x
x
x
x
Parameter 14-07 Dead Time Compensation Level
x
x
x
x
Parameter 14-08 Damping Gain Factor
x
x
x
x
Parameter 14-09 Dead Time Bias Current Level
x
x
x
x
Parameter 14-10 Mains Failure
x
x
x
x
Parameter 14-11 Mains Voltage at Mains Fault
x
x
x
x
Parameter 14-12 Function at Mains Imbalance
x
Parameter 14-27 Action At Inverter Fault
x
x
x
x
Parameter 14-40 VT Level
x
x
x
x
Parameter 14-41 AEO Minimum Magnetisation
x
x
x
x
Parameter 14-50 RFI Filter
x
Parameter 14-51 DC-Link Voltage Compensation
x
x
x
x
Parameter 14-55 Output Filter
x
x
x
x
Parameter 14-64 Dead Time Compensation Zero Current Level
x
x
x
x
Parameter 14-65 Speed Derate Dead Time Compensation
x
x
x
x
Parameter 30-22 Locked Rotor Detection
x
x
x
Parameter 30-23 Locked Rotor Detection Time [s]
x
x
x
Table 4.2 Active Parameters
1-10 Motor Construction
Option:
Function:
[0]
*
Asynchron
For asynchronous motors.
[1]
PM, non-
salient SPM
For permanent magnet (PM) motors with
surface-mounted (non-salient) magnets.
Refer to
to
parameter 1-17 Voltage filter time const.
for
details about optimising the motor
operation.
[2]
PM, salient
IPM, non Sat.
For permanent magnet (PM) motors with
interior (salient) magnets, without
inductance saturation control.
[3]
PM, salient
IPM, Sat.
For permanent magnet (PM) motors with
interior (salient) magnets, with inductance
saturation control.
1-14 Damping Gain
Range:
Function:
120
%
*
[ 0 -
250 %]
The damping gain stabilises the PM machine. The
value of damping gain controls the dynamic
performance of the PM machine. High damping
gain gives high dynamic performance and low
1-14 Damping Gain
Range:
Function:
damping gain gives low dynamic performance.
The dynamic performance is related to the
machine data and load type. If the damping gain
is too high or low the control becomes unstable.
1-15 Low Speed Filter Time Const.
Range:
Function:
Size related
*
[ 0.01 - 20
s]
This time constant is used below
10% rated speed. Obtain quick
control through a short damping
time constant. However, if this value
is too short, the control becomes
unstable.
1-16 High Speed Filter Time Const.
Range:
Function:
Size related
*
[ 0.01 - 20
s]
This time constant is used above
10% rated speed. Obtain quick
control through a short damping
time constant. However, if this value
Parameter Descriptions
VLT
®
AutomationDrive FC 360
28
Danfoss A/S © 7/2015 All rights reserved.
MG06C602
4
4
