VLT
®
FCM Series
Programming
340 Terminal 9, output functions (OUTPUT FUNC.)
Settings:
✭
No function
(NO OPERATION)
[0]
Ready signal
(UNIT READY)
[1]
Enable, no warning
(ENABLE/NO WARNING)
[2]
Running
(MOTOR RUNNING)
[3]
Running, no warning
(RUNNING NO WARNING)
[4]
Running on reference, no warning
(RUNNING ON REFERENCE)
[5]
Fault
(FAULT)
[6]
Fault or warning
(FAULT OR WARNING)
[7]
Current limit
(CURRENT LIMIT)
[8]
Thermal warning
(THERMAL WARNING)
[9]
Reversing
(REVERSE)
[10]
Control word bit 11
(CONTROL WORD BIT 11)
[11]
Actual frequency 0-20 mA
(0-FMAX = 0-20 mA)
[12]
Actual frequency 4-20 mA
(0-FMAX = 4-20 mA)
[13]
Reference
MIN
- reference
MAX
: 0-20 mA
(REF MIN-MAX =0-20 mA)
[14]
Reference
MIN
- reference
MAX
: 4-20 mA
(REF MIN-MAX =4-20 mA)
[15]
Feedback
MIN
- feedback
MAX
: 0-20 mA
(FB MIN-MAX =0-20 mA)
[16]
Feedback
MIN
- feedback
MAX
: 4-20 mA
(FB MIN-MAX =4-20 mA)
[17]
Actual current 0-20 mA
(0-IMAX = 0-20 mA)
[18]
Actual current 4-20 mA
(0-IMAX = 4-20 mA)
[19]
Mechanical brake
(MECHANICAL BRAKE)
[20]
Sleep mode
(SLEEP MODE)
[21]
Function:
This output can act both as a digital and an
analogue output. If used as a digital output (data
value [0]-[20]), a 24 V DC signal is transmitted;
if used as an analogue output either a 0-20 mA
signal, or a 4-20 mA signal output.
Description of choice:
Unit Ready signal
, the FC motor is ready for use.
Enable/no warning,
the FC motor is ready for
use; no start or stop command has been given
(start/ disable). No warning.
Motor Running,
the output frequency is higher than
0.1 Hz or a start command has been given.
Running no warning,
the output frequency is higher than
0.1 Hz. A start command has been given. No warning.
Running on reference,
no warning, speed according
to reference. No warning.
Fault,
output is activated by alarm.
Fault or warning
, the output is activated by
alarm or warning.
Current limit
, the current limit in parameter
221 has been exceeded.
Thermal warning,
above the temperature limit
in the frequency converter.
Reverse
. Logic
’
1
’
= relay activated, 24 V DC on the
output when the direction of rotation of the motor
is clockwise. Logic
’
0
’
= relay not activated, no
signal on the output, when the direction of rotation
of the motor is counter-clockwise.
Control word bit 11
, if bit 11 = "1" in the control
word (both Fieldbus Profile and FC Profile) the
digital output will be activated.
0-fMAX (parameter 202)
⇒
0-20 mA
and
0-fMAX (parameter 202)
⇒
4-20 mA
Reference
MIN
- Reference
MAX
: 0-20 mA
and
Reference
MIN
- Reference
MAX
: 4-20 mA
Feedback
LOW
- Feedback
HIGH
: 0-20 mA
and
Feedback
LOW
- Feedback
HIGH
: 4-20 mA
0-I
VLT, MAX
⇒
0-20 mA and
0-I
VLT, MAX
⇒
4-20 mA
Mechanical brake, enables
control of an
optional external mechanical brake (see also
parameter 138 and 139).
Sleep mode,
active when the unit is in sleep
mode. See section
Sleep mode.
✭
= factory setting. () = display text [] = value for use in communication via serial communication port
MG.03.H3.02 - VLT is a registered Danfoss trademark
57
