13-01 Start Event
Option:
Function:
[25]
Comparator 3
Use the result of comparator 3 in the
logic rule.
[26]
Logic rule 0
Use the result of logic rule 0 in the logic
rule.
[27]
Logic rule 1
Use the result of logic rule 1 in the logic
rule.
[28]
Logic rule 2
Use the result of logic rule 2 in the logic
rule.
[29]
Logic rule 3
Use the result of logic rule 3 in the logic
rule.
[33]
Digital input DI18 Use the value of DI18 in the logic rule
(High = TRUE).
[34]
Digital input DI19 Use the value of DI19 in the logic rule
(High = TRUE).
[35]
Digital input DI27 Use the value of DI27 in the logic rule
(High = TRUE).
[36]
Digital input DI29 Use the value of DI29 in the logic rule
(High = TRUE).
[39]
*
Start command
This event is TRUE if the frequency
converter is started by any means (either
via digital input, field bus or other).
[40]
Drive stopped
This event is TRUE if the frequency
converter is stopped or coasted by any
means (either via digital input, fieldbus
or other).
[42]
Auto reset trip
This event is TRUE if the frequency
converter is tripped (but not trip-locked)
and an Automatic Reset is issued.
[50]
Comparator 4
Use the result of comparator 4 in the
logic rule.
[51]
Comparator 5
Use the result of comparator 5 in the
logic rule.
[60]
Logic rule 4
Use the result of logic rule 4 in the logic
rule.
[61]
Logic rule 5
Use the result of logic rule 5 in the logic
rule.
[83]
Broken belt
A broken belt condition has been
detected. This function must be enabled
in
13-02 Stop Event
Option:
Function:
Select the condition (TRUE or FALSE)
which will deactivate the Smart Logic
Controller.
[0]
False
Enters the fixed value of FALSE in the
logic rule.
13-02 Stop Event
Option:
Function:
[1]
True
Enters the fixed value TRUE in the logic
rule.
[2]
Running
See
for further
description.
[3]
In range
See
for further
description.
[4]
On reference
See
for further
description.
[7]
Out of current
range
See
for further
description.
[8]
Below I low
See
for further
description.
[9]
Above I high
See
for further
description.
[16] Thermal warning
See
for further
description.
[17] Mains out of range See
for further
description.
[18] Reversing
See
for further
description.
[19] Warning
See
for further
description.
[20] Alarm (trip)
See
for further
description.
[21] Alarm (trip lock)
See
for further
description.
[22] Comparator 0
Use the result of comparator 0 in the
logic rule.
[23] Comparator 1
Use the result of comparator 1 in the
logic rule.
[24] Comparator 2
Use the result of comparator 2 in the
logic rule.
[25] Comparator 3
Use the result of comparator 3 in the
logic rule.
[26] Logic rule 0
Use the result of logic rule 0 in the logic
rule.
[27] Logic rule 1
Use the result of logic rule 1 in the logic
rule.
[28] Logic rule 2
Use the result of logic rule 2 in the logic
rule.
[29] Logic rule 3
Use the result of logic rule 3 in the logic
rule.
[30] SL Time-out 0
Use the result of timer 0 in the logic rule.
[31] SL Time-out 1
Use the result of timer 1 in the logic rule.
[32] SL Time-out 2
Use the result of timer 2 in the logic rule.
Parameters
VLT HVAC Basic Drive Programming Guide
MG.18.B1.02 - VLT
®
is a registered Danfoss trademark
51
3
3
