DB-70 Automatic Wheel Balancer
34
P/N 5900261 — Rev. A1 — January 2021
Note
: If the values appear incorrect you can turn off the power to reset the machine and
start the process over.
d.
Determine the width of the wheel using the wheel caliper and input this value using the front
panel button labelled
B
. The value should appear in the Outer Window.
e.
When all three measurements are correct, you are done entering measurements.
f.
Close the Tire Cover; the Wheel spins briefly.
⚠
WARNING
Stay clear and do not touch the Wheel or the Tire while it is rotating.
g.
The Balancer will automatically rotate and test the wheel for balance, unless the Tire Cover
switch is in the off position. If the Tire Cover switch is off, then lower the Tire Cover and
manually start the test using the start button on the control panel.
h.
The front panel display will show the unbalanced weight correction values for both the inner
and center wheel planes in ALU 1. These values are rounded to the nearest .25 oz. Press
F
to view the actual unbalanced weight without rounding. If either window displays
0.0
no
corrective weights are required on that plane.
i.
Check the value on the Inner Window.
•
If the value is
00
, you do not need to add weight to the Inner Plane.
•
If there is a value—
.25
, for example—you need to add that amount of Weight to the
Inner Plane.
j.
To add Weight, break off the appropriate number of Adhesive Weight sections.
k.
Turn the Wheel, watching the indicators to the
right
of the
Inner Display Window
.
•
The Indicators light up or go out as you move the Wheel.
l.
When all of the Indicators are lit, press the Brake Pedal to hold the Wheel at that position.
m.
Pull the backing off the Adhesive Weights, then add the Weight at Top Dead Center on the
Wheel (12 o’clock high) on the Inner Plane. If you are adding Adhesive Weight with multiple
sections, center them on Top Dead Center.
n.
Check the value on the
Outer Display Window
o.
If the value is
00
, you do not need to add Weight to the Center Plane.
p.
If there is a value—
.25
, for example—you need to add that amount of Weight to the
Center Plane for
ALU 1
).
q.
To add Weight, break off the appropriate number of Adhesive Weight sections.
r.
Manually turn the Wheel, watching the indicators to the
left
of the
Outer Display
Window
. The Indicators light up or go out as you move the Wheel.
s.
When all of the Indicators are lit, press the Brake Pedal to hold the Wheel at that position.
t.
Pull the backing off the Adhesive Weights, then add the Weight at Top Dead Center on the
Wheel (12 o’clock high) on the Center Plane for ALU1. If you are adding Adhesive Weights
with multiple sections, center them on Top Dead Center.
u.
Release the Brake Pedal.
v.
Lower the Tire Cover to spin the Wheel again.
Summary of Contents for DB-70
