background image

P

AGE

 20

44210/49210-0798 <90-00025>

FCC REQUIRED INFORMATION

T

he following are requirements of Part 68 of FCC Rules:

1.

The installer of this equipment is responsible for notifying the tele-
phone company that it is being connected or disconnected.

2.

This equipment is not to be connected to party lines or coin tele-
phone service.

3.

The telephone company has the right to temporarily discontinue
service (Section 68.108) and to change facilities and services which
may affect the operation of this equipment. Adequate written no-
tice will be provided to the user to maintain uninterrupted service
(Section 68.110B).

4.

In case of trouble, contact the manufacturer’s authorized agent.

5.

When the installation of this device requires connection or changes
to the internal wiring of registered telephones or other registered
devices, such changes and connections can be made only by the
registered grantee or authorized agents, equipment manufacturers,
registered telephone refurbishers, telephone companies, and those
qualified for the installation of KN and PN systems under Section
68.215 of the rules. The installer of this equipment is advised, in
the interest of safety, that the host equipment be disconnected from
all power sources and the telephone network when the installation
is being made.

6.

Installation of this equipment as an adjunct can be made only with
permission of the owner of the host equipment.

FCC required information pertaining to this module:

Registration Number:  DPH622-60575-MD-E

Summary of Contents for 44210























Reviews: