background image

4

Introduction

: Overview

Overview

The target group for this service manual is the technicians who install and maintain the CDP 

40-50-70 and CDP 40T-50T-70T dehumidifier. Thus the manual covers instructions about 

installation, operation and maintenance.

It is the responsibility of the operator to read and understand this service manual and other 

information provided and to use the correct operating procedure.
Read the entire manual before the initial start-up of the unit. It is important to know the cor-

rect operating procedures for the unit and all safety precautions to prevent the possibility of  

property damage and/or personal injury.
 

It is the responsibility of the installer to ensure the conformity of all, not supplied cables 

towards national regulations.

Copying of this service manual, or part of it, is forbidden without prior written permission 

from Dantherm.

Dantherm reserves the right to make changes and improvements to the product and the 

service manual at any time without prior notice or obligation.

The unit is designed to last for many years. When the time comes for the unit to be recycled, it 

should be recycled according to national rules and procedures to protect the environment.
The CDP dehumidifiers contain R407C refrigerant and compressor oil. The compressor must 

be returned to authorities for disposal according to local regulations. 

Type and source of hazard

 This symbol in connection with the word “Danger” warns of a high risk or severe injury or 

acute danger to life.

•  Measures to avert danger or immediate measures if the risk occurs are described in this 

way

Type and source of hazard

 This symbol in connection with the word “Warning” warns of a risk involving severe injury.

•  Measures to avert danger or immediate measures if the risk occurs are described in this 

way

Type and source of hazard

This symbol in connection with the word “Caution” warns of a risk of minor or moderate injury 

and material damage.

•  Measures to avert danger or immediate measures if the risk occurs are described in this 

way

In connection with this symbol you will find further tips and information concerning the use 

of the device.

Target group

Safety precautions

Copyright

Reservations

Recycling

Warning

Caution

DANGER

Warning

Caution

WARNING

Warning

Caution

CAUTION

!

NOTICE

Summary of Contents for CDP 40









































Reviews: