background image

4

.

Ducting

4.1  Introduction

There are many ways to install dehumidifiers, including non-ducted installation, ducting for fresh Air, 

installation with HVAC system,etc.

Please read the manual carefully and consult relevant technicians and experts before installation.

4.1.1   Independent operation of dehumidifier

Put the dehumidifier in the room independently, so that the humidity in the room will drop quickly, without 

connecting the pipes.

Do not draw air directly from the kitchen or washing machine room as fresh air. The dehumidifier can be placed 

outdoors to extract air as fresh air and then sent to a separate space after dehumidification, such as: paint spray 

room, purification room.

4.1.2  Ducting for Fresh Air

Dry air

Wet air

Wet fresh air

Dry fresh air

4.1.3  Installation with HVAC system

To dehumidify with HVAC system, place the dehumidifier outdoors, and connect the air outlet of the 

dehumidifier to the fresh air inlet of the AC unit to complete the matching. The humid outdoor air pass 

through the dehumidifier and then into the AC unit. The indoor return air of the AC unit is mixed with the 

dehumidified fresh air and sent into the room, which can reduce the humidity in the clean room and meet the 

process requirements in the workshop.

Dehumidifier

Supply air

Return air

Fresh air

13

14

Summary of Contents for DEH-10K




















Reviews: